Hagie NTB Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 31

Hagie NTB Series Скачать руководство пользователя страница 4

ii

INTRODUCTION

TO THE OPERATOR:

The following pages and illustrations will help you operate and service your Nitrogen Toolbar.

It is the responsibility of the user to read the Operator’s Manual and comply with the safe operating

procedures and the proper lubrication and maintenance schedules.

The user is responsible for inspecting the attachment, having parts repaired or replaced when

continued use of the product causes damage or excessive wear to other parts.

Keep this manual in a convenient place for easy reference when problems arise. This manual is

considered a permanent fixture with this attachment. In the event of resale, this manual should

accompany the unit. If you do not understand any part of the manual or require additional

information or service, contact the Hagie Customer Support Department:

Hagie Manufacturing Company

721 Central Avenue West

Box 273

Clarion, Iowa 50525-0273

(515) 532-2861

The following symbols found throughout this manual alert you to situations that could

be potentially dangerous to the operator, service personnel or the equipment.

This symbol indicates a hazardous situation

which, if not avoided, will result in death or serious

injury.

This symbol indicates a potentially hazardous

situation, which if not avoided, could result in

death or injury.

This symbol indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury. It may also be used to alert

against unsafe practices.

«
...
2
3
4
5
6
...
»

Содержание NTB Series
































Отзывы:

Нет отзывов