manualshive.com logo in svg

Hagie NTB Series, Руководство оператора, Страница: 29 / 31

Поделиться
Скачать
Hagie NTB Series Скачать руководство пользователя страница 29

24 

 

STORAGE 

Preparing for Storage 

1.

 

Perform daily and weekly lubrication and 

maintenance inspections as required. 

 

2.

 

With the engine at normal operating 

temperature, cycle all the hydraulic 

functions.  

3.

 

Thoroughly rinse the spray system. To 

winterize the spray system, it is 

recommended that you use an 

environmentally safe type of antifreeze 

and water mixture that will give you 

adequate protection to –30°. Drain any 

remaining solution in the spray system and 

run the antifreeze mixture through the 

system until it comes out all attachment 

openings. Repeat the above procedure 

with the foam marker (if equipped) and the 

rinse systems.  

 

4.

 

Refer to the Raven manual for detailed 

information on storage procedures for the 

monitor and flow meters.  

5.

 

Thoroughly wash the boom and touch up 

any chipped or damaged paint. For touch 

up paint recommendations, contact Hagie 

Customer Service.  

6.

 

Replace any damaged or missing decals. 

Warning decals and all other Hagie decals 

are available through Hagie Customer 

Service.  

7.

 

Use multi-purpose grease to coat exposed 

hydraulic cylinder rods.   

8.

 

If the NTB attachment will be stored 

separately from the sprayer, be sure that 

all open ends are capped or covered with 

a suitable covering.  

_________________________________________________________________________________ 

Removing from Storage 

1.

 

Remove any dried grease from cylinder 

rods and reapply if necessary. 

 

2.

 

Completely clean the NTB attachment.  

3.

 

Carefully unseal any openings that were 

sealed for storage. 

4.

 

Attach NTB to sprayer and manually cycle 

the hydraulics 2 or 3 times to thoroughly 

lubricate components.  

 

Содержание NTB Series
































Отзывы:

Нет отзывов