Hafler GX2800 Скачать руководство пользователя страница 21

Страница: 21 / 24

– 19 –

1. Connect signal from source to CH B input.
2. Biamp/Stereo switch not active-(Stereo/Mono switch

overrides this switch when in mono/70V/100V mode).

3. Move Stereo/Mono switch to MONO mode.
4. Set load switches (8

Ω

) to 1/2 the actual load

impedance. (16

Ω

) i.e. for a 4

Ω

speaker load,

select the 2

Ω

setting for both CH A and CH B Load

Switches

5. Connect appropriate speaker load 16

Ω

across

the red terminals of the 5-way binding posts. CE units:
Wire SPEAKON as shown above and connect to CH A
output.

6. CH B level control adjusts the mono output level.

BRIDGE MONO MODE

CE SPEAKON
Connector
Wiring

Connect to CH A output

1. Connect signal from source to CH B input.
2. Biamp/Stereo switch not active (Stereo/Mono switch

overrides this switch when in mono/70V/100V mode).

3. Move Stereo/Mono switch to 70V mode.
4. Select 70V load, both channels.

5. Connect parallel array of 70V transformer-equipped

speakers across the red terminals of the 5-way binding
posts. CE units: Wire SPEAKON as shown above and
connect to CH A output.

6. CH B input sensitivity controls 70V mono output level.

Amplifier will clip at 70Vrms level.

70V MONO MODE

CE SPEAKON
Connector
Wiring

Connect to CH A output

Содержание GX2800

























Результаты поиска

Содержание GX2800

Отзывы:

Похожие инструкции для GX2800

Бренды по названию

Популярные бренды

Hafler GX2800, Руководство пользователя

Результаты поиска

Содержание GX2800

Отзывы:

Похожие инструкции для GX2800

Бренды по названию

Популярные бренды