Hafco Metalmaster EB-280DSV Скачать руководство пользователя

Страница: 25 / 33

OPERATION MANUAL

SYMPTOM

POSSIBLE CAUSE

ACTION REQUIRED

Machine does not

start

1. Emergency Stop button pressed

2. Power Supply in the OFF position

3. Motor ON/OFF switch is faulty

4. Faulty Motor

1. Reset the E-Stop by twisting the button

2. Check power supply is ON and not faulty

3. Test and replace the switch

4. Test and replace the motor.

Machine stalls or

seems underpow-

ered

1. Wrong blade for the work piece

2. Feed rate to fast for the blade

3. Blade is slipping on the wheels

4. Motor over heating

5. Motor is faulty

1. Change to the correct blade

2. Decrease the feed rate

3. Adjust the blade guides and the tension

4. Let the motor cool and reduce the work load

5. Test and replace

Machine is noisy or

vibrates

1. Blade is faulty

2. Motor fan is rubbing on cover

3. Speed is set too slow

1. Replace with new or correct blade

2. Adjust and tighten fan or replace

3. Adjust the speed to suit the work piece

Machine bogs down

or is loud

1. Excessive feed rate

2. The blade T.P.I. is too great for the

material

1. Reduce the feed rate

2. Check for the correct blade (Page 16)

Blades Breaking

1. Blade is not tension correctly

2. Loose work piece

3. The feed or cutting speed is wrong

4. Incorrect blade selection

5. The blade is too thick or low quality

1. Check the blade tension (Page 13)

2. Re-clamp the work piece tighter or use a jig

3. Adjust the feed rate and the speed (Page14)

4. Refer to blade selection (Page 16)

5. Use better quality blade

Teeth breaking of the

blade

1. The feed is too great

2. The blade T.P.I. is too course

3. Blade gullets are loaded up with

chips

1. Decrease the blade pressure

2. Refer to blade selection (Page 16)

3. Use a coarser tooth blade

The cuts are crooked

1. The feed pressure is too high

2. The blade tension is low

3. The blade is dull

1. Reduce the feed rate

2. Adjust the blade tension as required.

3. Replace the blade.

5.8 TROUBLE SHOOTING

If the machine develops a problem, review the trouble shooting section below to find a fix for

the problem. If the problem cannot be solved then contact your dealer for help or to book a

service engineer.

Page 25

Instruction Manual for EB-280DSV (B063V)

10/04/2019

Содержание EB-280DSV


































Результаты поиска

Содержание EB-280DSV

Отзывы:

Похожие инструкции для EB-280DSV

Бренды по названию

Популярные бренды

Hafco Metalmaster EB-280DSV, Руководство по эксплуатации

Результаты поиска

Содержание EB-280DSV

Отзывы:

Похожие инструкции для EB-280DSV

Бренды по названию

Популярные бренды