Haes ESPRIT-G Скачать руководство пользователя | Manualshive

Страница: 23 / 88

background image

ESPRIT Gas Extinguishing User Manual

INSTALLATION

23

Approved Document Ref: UI-ESG-01 Issue 2.0

Relay Outputs

The panel is equipped with six relay outputs. Each output is unsupervised with volt-free changeover
contacts rated at 30VAC/DC, 1A, resistive.

The Fault Relays and Fire Relays are fixed to indicate their respective conditions.

The Fault Relay is normally activated. It will de-energise on any fault condition from an active zone
including total loss of power.

Local Relay operates on activation of a zone that is part of the extinguisher release circuitry, or when
the panel mounted (or remote manual) release pushbutton is pressed. The relay remains activated
until the panel is reset. All Relay outputs are programmable.

Extract Fan Relay operates when an authorized (Access Level 2) user selects Start Extract Fan, after
the flooding time has elapsed (without a reset). This allows a flooded area to be vented of extinguishing
medium.

Local Fire Relay operates on activation of a fire condition in a Flood Zone.

Stage 1 Relay has a default operation, which is ON during the pre-activation, activation and release
stages.

Stage 2 Relay will come ON only during the release stage. This status is settled by default and can be
changed.

Both relays, for stage 1 and stage

2, are fully programmable, and they can take the following values:

a) ON / OFF

b) Pulsing 1 sec ON and 1 sec OFF

Additional Relays

If additional relays are required, then install the OPCARD-8 8-Way Relay card to piggy-back onto the
COMs A header on the PSU Card

Connect the 10-Way ribbon cable between the relay card and the main display card

– the connectors

are polarised to prevent incorrect connection.

8 changeover volt-free relay outputs are provided. Each is rated at 30VAC/DC, 1A, resistive. All Relay
outputs are programmable.

«
...
21
22
23
24
25
...
»

Содержание ESPRIT-G

























































































Отзывы:

Нет отзывов

Похожие инструкции для ESPRIT-G

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: BADLANDS Страницы: 2

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Lawler Страницы: 5

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды