HADEF 70/06AP-EX Скачать руководство пользователя страница 22

Страница: 22 / 32

5.52.541.01.01.09

CAUTION!

The maintenance units are not approved for use with synthetic oil.

They must not be connected to compressed air systems which are supplied by compressors with synthetic
lubricants.

9.3

Gear

NOTICE!

For transport, some gear types are fitted with a plug screw. Replace the plug screw by a ventilation screw
(attached) before putting the unit into operation.

9.4

Load chain



Before commissioning the load chain must be aligned and oiled.



Move safety note and fixing wire away from the chain.

9.5

Power operated hoists with chain container:

Due to the transport and / or installation of the hoist on the beam, the position of the load chain in the chain
container can change unfavorably.

WARNING!

It is mandatory before the first commissioning:



that the complete load chain without load with the utmost care from the chain

container is driven



i.e. when lowering, pay special attention to the load chain on the chain container

side, so that the load chain can run properly through the hoist without being twisted



only after the chain container is completely empty, the load chain without load, can

be returned to the chain container



during the running in of the load chain, lubricate it over its entire length

CAUTION!

Do not use grease for lubrication of load chain.

Without lubrication, manufacturer's warranty and/or liability will be void.

NOTICE!

Continuous, thorough lubrication will increase the life of the chain considerably.

Safety check

Before putting into service initially or when putting back into service, it must be checked whether:



All fastening screws (if existent), socket pins, flap socket and safety devices are tightened and secured.



The oil levels in the gear boxes are sufficient.



All movements of the load comply with the symbols on the control switch.



The chains are correctly placed, oiled and in good condition.

Содержание 70/06AP-EX

































Результаты поиска

Содержание 70/06AP-EX

Отзывы:

Бренды по названию

Популярные бренды

HADEF 70/06AP-EX, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 70/06AP-EX

Отзывы:

Бренды по названию

Популярные бренды