20
5.52.180.00.01.07
13.3
Checking the load chain
acc. DIN 685-part 5
L11 = pitch increase over 11 chain links
L1 = pitch increase over 1 chain link
dm = detected link thickness
Illustration 16
Pos: 17.4.3.2 /1_HADEF/13-PRÜFUNG/Kettenzug/Lastkette/Tabelle - Ketten 5 - 7 - 9 @ 2\mod_1279548151411_52.docx @ 14848 @ @ 1
Chain dimensions
Dimensions
mm
Chain size
5x15
7x21
9x27
L11
171,4
238,8
300,8
L1
16,0
22,4
28,1
dm
4,6
6,5
8,2
Pos: 17.4.3.3 /1_HADEF/---ALLGEMEIN/Hinweise/Ketten/WARNUNG - Ketten: Bei Erreichen der Tabellenmaße durch Verschleiß oder Verformung die Ke @ 0\mod_1178705158838_52.docx @ 5763 @ @ 1
WARNING!
When the dimensions listed in the table are reached due to wear or deformation, the chain must be
replaced!
Pos: 17.4.4.1 /1_HADEF/13-PRÜFUNG/Kettenzug/Lasthaken/Lasthaken - Maßerklärung - X-Y-H @ 0\mod_1182346659653_52.docx @ 6318 @ @ 1
13.4
Checking the load hook
Load hook
X = measuring distance hook mouth width
Y = measured length from hook no. 6
H = thickness of hook saddle
Illustration 17
Pos: 17.4.4.2 /1_HADEF/13-PRÜFUNG/Kettenzug/Lasthaken/Tabelle - Hakenmaße - 29/06E-Synchro @ 2\mod_1279548585622_52.docx @ 14856 @ @ 1
Dimension
mm
Capacity in t/ chain falls
0,5 1/2
2/2
2,5/2
3,2/2
hook nr.
04 04
08
1
1
X
32 32
38
40
40
H
29 29
37
40
40
Dimensions in the tables are theoretical values without tolerances.
Please fill in the measured
values before
commissioning:
Capacity t
X or Y
mm
H mm
Pos: 17.4.4.3 /1_HADEF/---ALLGEMEIN/Hinweise/Haken/VORSICHT - Haken bei Verformung.... @ 0\mod_1177582461489_52.docx @ 5510 @ @ 1
CAUTION!
When the dimension of hook opening width is deformed more than 10% or when the dimension of the hook
bottom thickness is fallen short of by 5% due to wear, the hook must be replaced.
Pos: 17.4.5 /1_HADEF/13-PRÜFUNG/Kettenzug/Getriebe/AK Ölstand prüfen @ 3\mod_1389865965388_52.docx @ 27460 @ @ 1
13.5
Inspection – Gear – Oil level
Check oil level all 3 month.
Locking
screw(C)
Tool
AK 4-8 AK9-10
AK 4 – AK 6
M10 SW8
AK 7 – AK 8
M12 SW10
Solve the locking screw (C) a bit. (do not remove)
If oil drips out = level OK.
Tighten the screw.
If no oil drips out, carry out maintenance and oil change.
(see chapter maintenance)
AK 9 - 10
Oil gauge glass (C)
Oil gauge glass half full = level OK
No oil observable = carry out maintenance and oil change.
(see chapter maintenance)
Pos: 18.1 /1_HADEF/14-WARTUNG/*Ü1*/#. Kapitel - Wartung @ 0\mod_1172647693186_52.docx @ 409 @ @ 1
