background image

 

 

X-Pro 
Speedcontroller

 

       

 
 

Dear Customer, 
 
 
Thank you for your purchase of the 

X- Pro-Series Controller, 

a new generation of sensorless 

speed controllers especially for 

’Hacker Brushless A-Series- Motors’ 

and other Brushless Motor 

Designs. Special programming options are provided to ensure the best possible power and 
performance from your motor system. ‘

Brushless

’ systems offer high power efficiency combined 

with low weight and compact dimensions. For best performance and reliability from your 
Controller, use only High quality connectors, motors and batteries.  

Please, pay careful attention to the following instructions before you start to work with 
your new motor and speed controller.

 

 
 
 
 

Connections:  

  
The speed controller can be connected to the motor by direct soldering or with high quality 
connectors. Always use new connectors, which should be soldered carefully to the cables and 
insulated with Heat-shrink tubing.  It is possible to extend the cables to the motor battery pack up 
to a maximum of 8 inches. Deans Ultra or other high quality connectors are recommended for 
connecting the motor battery pack to the controller.   

 

Solder Controller  to the Motor wires 

 

Solder appropriate connectors to the Battery wires 

 

Insulate all Solder connections with Heat Shrink Tubing. 

 

Plug the JR connector into the receiver throttle channel. 

 
When connecting controller to battery pack, care should be taken to ensure that multiple touches 
of the connectors are not made. 
Reversing the motor directions is achieved by the exchanging the position of any two wires 
connected to the motor or by programming “rotation reverse”.

 

 
 
 
 

 

Installing the Controller:

 

 
Install the speed controller in the model so that it is isolated from vibration and shock, using Velcro 
or double sided foam tape. Allow space around it for cooling. Make sure that there is sufficient 
cooling of the motor and speed controller by ducting air through adequate cooling holes from the 
outside airflow. Main power packs should be connected at one attempt.  
 

Copyright 06/07 – Hacker Motor GmbH   1 

Содержание Pro Series







Отзывы: