manualshive.com logo in svg

HACH LANGE ORBISPHERE 3654, Руководство пользователя, Страница: 52 / 58

Поделиться
Скачать
HACH LANGE ORBISPHERE 3654 Скачать руководство пользователя страница 52

50

Maintenance and Troubleshooting

8.6.4 Troubleshooting table

Table 6  Troubleshooting table

Symptom

Cause

Possible Solution

Unstable
measurement

Degassing

Adjust sample flow rate

Flow chamber and/or membrane not clean

Clean system

Sensor’s membrane not tight smooth and 
wrinkle free

Replace membrane and 
recalibrate

Leaking solenoid valve

No gas bubbles should escape from 
the purge gas outlet during 
measurement. If the solenoid leaks 
(more than 1 bubble in 15 seconds) 
contact your Hach Lange 
representative.

An external power supply is used but the 
power supply is not clean

Switch to battery power

Low readings

Sample flow rate too low

Check flow rate

Degassing

Adjust forcing gas and/or sample flow 
rate

Membrane is not at sample temperature

Allow sample to flow past the 
membrane to make sure the 
membrane is at sample temperature 
before making measurements

Membrane not clean

Clean system

Incorrect solubility curve

Change solubility

Incorrect calibration

Recalibrate

High readings

Membrane is not at sample temperature

Allow sample to flow past the 
membrane to make sure the 
membrane is at sample temperature 
before making measurements

Incorrect solubility curve

Change solubility

Incorrect calibration

Recalibrate

Содержание ORBISPHERE 3654



























































Отзывы:

Нет отзывов