HACH LANGE ORBISPHERE 3654 Скачать руководство пользователя страница 46

Страница: 46 / 58

Maintenance and Troubleshooting

Note:

Distinguish the membrane from the protection paper:

- Membrane is transparent (translucent).
- Protection paper is opaque.

The membrane diameter is larger than the sensor head
diameter. This is normal, as the membrane will fold over the
sensor tip.

The membrane holding ring comes in two slightly different
internal diameters, depending on the membrane(s) total
thickness.

For a correct membrane installation, be sure to use the
correct holding ring for the application.

If mounting dual membranes, always use mounting ring part
number 29229.

Place the membrane holding ring on the installation tool tip.

CAUTION
To avoid damaging the membrane, make sure that the
tool tip is totally clean and its surface is even.

Insert the installation tool inside the guiding sleeve.

Push the installation tool firmly downwards. This clasps the
mounting ring onto the sensor head, folding the membrane
over the sensor tip.

Remove the installation tool and guiding sleeve.

Visually check for correct ring placement, try to push it down
with your fingers.

Check that the membrane is tight, with no wrinkles.

Clean and dry the protection cap ready for installation.

Replace the O-ring inside the protection cap with a new one.
Tighten the protection cap finger tight.

Then, complete the process using the tool provided in the
maintenance kit. Insert into each of the four holes in turn, and
tighten as far as possible. Tighten each hole only once.

Содержание ORBISPHERE 3654



























































Результаты поиска

Содержание ORBISPHERE 3654

Отзывы:

HACH LANGE ORBISPHERE 3654, Руководство пользователя, Страница: 46 / 58

Результаты поиска

Содержание ORBISPHERE 3654

Отзывы: