background image

1

96-0041 Rev U

July 2010

1.  WARRANTY

All new HAAS Toolroom Mills are warranted exclusively by the Haas 

Automation’s (“Manufacturer”) limited warranty against defects in material and 

workmanship for a period of one (1) year from the date of purchase, which is 

the date that a machine is installed at the end user. See the Warranty section 

of the Mill Operator’s Manual for further warranty information.

2. SAFETY

Read and Follow all safety warnings

  - Familiarize yourself with the 

Operator’s Manual Safety chapter. Be aware of the other people around you 

in the shop; flying chips can seriously injure people, who may not be a safe 

distance away. Always wear safety glasses. Initial cuts/setups should be cut at 

a slower speed to reduce the possibility of tool or machine damage.

3.  INSTALLATION

NOTE

:   These installation recommendations are to be used in conjunction 

with those in the Reference Manual. Material supplied here is 

given specifically for the Toolroom Mill.

e

lecTriciTy

 r

equiremenTs

IMPORTANT!  REFER TO LOCAL CODE REQUIREMENTS BEFORE 

WIRING MACHINES.

• The power source must be grounded

 

• Frequency range is 47-66 Hz

 

• Line voltage that does not fluctuate more than +/-5%

 

• Voltage imbalance or no more than 2%

 

• Harmonic distortion is not to exceed 10% of the total RMS voltage

  

 

 

       

 

Voltage Requirements

    

Toolroom Mill

 

 

 

         208 3PH / 240V 1PH ±10% 

 

Power Supply 

 

 

 

        40 AMP   

 

 

Haas Circuit Breaker 

 

  

        40 AMP   

 

  

If service run from elec. panel  

is less than 100’ use: 

 

     1PH - 8 GA WIRE/3PH - 10 GA WIRE 

If service run from elec. panel 

 is more than 100’ use: 

 

      1PH - 6 GA WIRE/3PH - 8 GA WIRE 

WARNING!

A separate earth ground wire of the same conductor size as input power is 

required to be connected to the machine chassis. This ground wire is required 

for operator safety and proper operation. This ground must be supplied from 

the main plant ground at the service entrance, and should be routed in the 

same conduit as input power to the machine. A local cold water pipe, or ground 

rod adjacent to the machine cannot be used for this purpose.

Содержание Toolroom Mill















Отзывы: