H3C S9500 Series Скачать руководство пользователя страница 175

Страница: 175 / 204

Operation Manual – VLAN
H3C S9500 Series Routing Switches

Chapter 2 Super VLAN Configuration

2-3

2.3 Displaying Super VLAN

To do…

Use the command…

Remarks

Display the mapping
between a super VLAN
and its sub-VLAN(s)

display supervlan

[

supervlan-id

]

Available in any view

2.4 Super VLAN Configuration Example

I. Network requirements

Create super VLAN 10, and configure the VLAN interface IP address of the super

VLAN as 10.0.0.1/24.

Create the sub-VLANs: VLAN 2, VLAN 3, and VLAN 5.

Ports Ethernet 0/1/1 and Ethernet 0/1/2 belong to VLAN 2, Ethernet 0/1/3 and

Ethernet 0/1/4 belong to VLAN 3, and Ethernet 0/1/5 and Ethernet 0/1/6 belong to

VLAN 5.

Through configuration, the sub-VLANs are isolated at Layer 2 but connected at

Layer 3.

II. Network diagram

Figure 2-1

Network diagram for super-VLAN configuration

III. Configuration procedure

# Create VLAN 10, configure its VLAN interface address as 10.0.0.1/24.

<Sysname> system-view

[Sysname] vlan 10

[Sysname-vlan10] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] ip address 10.0.0.1 255.255.255.0

# Enable local proxy ARP.

Содержание S9500 Series













































































































































































































Результаты поиска

Содержание S9500 Series

Отзывы:

H3C S9500 Series, Руководство по эксплуатации, Страница: 175 / 204

Результаты поиска

Содержание S9500 Series

Отзывы: