H3C S5810-50S Скачать руководство пользователя страница 68

Страница: 68 / 73

6-3

The S5810 series use hot swappable fan trays. When a fan tray failure occurs, you can follow these
steps to replace the fan tray.

Removing a Fan Tray

You can replace a hot swappable fan tray without powering off the device. To prevent overheat, you are
recommended to complete replacing the fan tray within two minutes.

1) Wear an ESD-preventive wrist strap, make sure that the wrist strap has a good skin contact and is

well grounded.

2) Loosen the screw on the fan tray with a Phillips screwdriver until the screw is completely separated

from the device, as shown in

Figure 6-1

Figure 6-1

Remove an LSW1BFAN (1)

3) Holding the handle of the fan tray with one hand, pull part of the fan tray out. Then supporting the

bottom of the fan tray with the other hand, pull it straight out of the fan tray slot along the guide rails,
as shown in

Figure 6-2

Figure 6-2

Remove an LSW1BFAN (2)

Содержание S5810-50S










































































Результаты поиска

Содержание S5810-50S

Отзывы:

H3C S5810-50S, Руководство по установке, Страница: 68 / 73

Результаты поиска

Содержание S5810-50S

Отзывы: