H3C H3C S5100-EI Скачать руководство пользователя страница 402

Страница: 402 / 934

Operation Manual – DHCP
H3C S5100-SI/EI Series Ethernet Switches

Chapter 1 DHCP Overview

1-3

Note:

After the client receives the DHCP-ACK message, it will probe whether the IP

address assigned by the server is in use by broadcasting a gratuitous ARP packet. If

the client receives no response within specified time, the client can use this IP

address. Otherwise, the client sends a DHCP-DECLINE message to the server and

requests an IP address again.

If there are multiple DHCP servers, IP addresses offered by other DHCP servers are

assignable to other clients.

1.2.3 Updating IP Address Lease

After a DHCP server dynamically assigns an IP address to a DHCP client, the IP

address keeps valid only within a specified lease time and will be reclaimed by the

DHCP server when the lease expires. If the DHCP client wants to use the IP address for

a longer time, it must update the IP lease.

By default, a DHCP client updates its IP address lease automatically by unicasting a

DHCP-REQUEST packet to the DHCP server when half of the lease time elapses. The

DHCP server responds with a DHCP-ACK packet to notify the DHCP client of a new IP

lease if the server can assign the same IP address to the client. Otherwise, the DHCP

server responds with a DHCP-NAK packet to notify the DHCP client that the IP address

will be reclaimed when the lease time expires.

If the DHCP client fails to update its IP address lease when half of the lease time

elapses, it will update its IP address lease by broadcasting a DHCP-REQUEST packet

to the DHCP servers again when seven-eighths of the lease time elapses. The DHCP

server performs the same operations as those described above.

1.3 DHCP Packet Format

DHCP has eight types of packets. They have the same format, but the values of some

fields in the packets are different. The DHCP packet format is based on that of the

BOOTP packets. The following figure describes the packet format (the number in the

brackets indicates the field length, in bytes):

Содержание H3C S5100-EI







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S5100-EI

Отзывы:

Похожие инструкции для H3C S5100-EI

Бренды по названию

Популярные бренды

H3C H3C S5100-EI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S5100-EI

Отзывы:

Похожие инструкции для H3C S5100-EI

Бренды по названию

Популярные бренды