background image

19

GT4.0 TREADMILL

TROUBLESHOOTING

CONSOLE

Item 

 

trouble 

Maintenance   

E1 

Communication 
abnormal:The 
communication 
between 

the 

controller  and  the 
electronic  watch  is 
abnormal 

after 

power is applied.

 

Broken  controller  couldn’t  working.  Console  display 
fault code and the buzzer sounded    3 times.

 

Reason:  the  poor  communication  between  controller 

and 

console. 

Checking 

each 

connection 

of 

communication wire between console and controller. 
Make sure    each core is completely inserted. Check 
the connection wire, if it was broken, change it.

 

E3 

The motor line is not 

connected properly

 

The treadmill stop working and enter a fault state when 
the buzzer sounded    9 times. The console display fault 
code  while  the  rest  areas  do  not  display  anything.  If 
console  discovery  normal  state  and  enter  standby  state 
after treadmill stop working, the treadmill can restart.

 

Reason:  make  sure  the  well  connection  of  the  motor 
wire  and  connect  the  wire  again.  If  the  controller  has 
peculiar smell, replace the controller.

 

No  signal  of  speed 
sensor:  a  voltage  from 
controller  is  output  to 
the  DC  motor.  The 
motor speed feedback is 
not 

continuously 

received for more than 3 
seconds.

 

The treadmill stop working and enter a fault state when 
the buzzer sounded    9 times. The console display fault 
code while the rest areas do not display anything. After 
maintaining  the  fault  state  for  about  10  seconds,  enter 
the standby state and restart the machine.

 

Reason:  no  speed  sensor  signal  is  detected  for  3 
consecutive  seconds,  check  whether  the  sensor  plug  is 
not  plugged  in  or  damaged,  plug  it  in  or  replace  the 
sensor.

 

E4 

Ascending 

by 

self 

learning

 

Check whether the induction line of the lifting motor is 
plugged  in  properly  and  plug  the  connector  again  to 
make  it  reliable.  Check  whether  the  AC  line  of  the 
lifting  motor  is  plugged  correctly,  and  the  AC  line  of 
the lifting motor is correctly numbered with the mark on 
the controller. Check whether the connecting wire of the 
motor is damaged or open, replace the connecting wire 
or  lift  the  motor;  After  checking  all,  press  the  learning 
key on the control to learn again.

 

E5 

Over 

current 

protection

˖

under  the 

running  state,  the  down 
control 

continuously 

detects  that  the  DC 
motor  current  is  greater 
than  the  rated  current 
+6A  for  more  than  3 
seconds.

 

The treadmill stop working and enter a fault state when 
the buzzer sounded    9 times. The console display fault 
code while the rest areas do not display anything. After 
maintaining  the  fault  state  for  about  10  seconds,  enter 
the standby state and restart the machine. 

Reason:  over  -  rated  load  leads  to  over-current  and 
self-protection  of  the  system,  or  a  certain  part  of  the 
treadmill  is  stuck,  resulting  in  motor  failure,  over-load 
and  over-current  and  self-protection  of  the  system. 
Adjust  the  treadmill  and  restart  it.  Check  whether  the 
motor  has  over-current  sound  or  burnt  smell  when 
running,  and  replace  the  motor;  Or  check  whether  the 
controller has burnt smell and replace the controller; Or 
check whether the power supply voltage specification is 
inconsistent  or  low,  and  retest  with  the  correct  voltage 
specification.

 

E6

 

Explosion 

proof 

protection: 

abnormal 

power supply voltage or 
abnormal  motor  will 
cause  damage  to  the 
drive motor circuit.

 

The treadmill stop working and enter a fault state when 
the buzzer sounded    9 times. The console display fault 
code while the rest areas do not display anything. After 
maintaining  the  fault  state  for  about  10  seconds,  enter 
the standby state and restart the machine. 

Reasons:  check  whether  the  power  supply  voltage  is 
lower  than  50%  of  the  normal  voltage,  please  retest 
with  the  correct  voltage  specification;  Check  whether 
the  controller  has  peculiar  smell  and  replace  the 
controller;  Check  whether  the  motor  line  is  connected 
properly and reconnect the motor line.

 

LCD display 

no value of 

pulse

 

A.

 The 

handle 

communication  wire 

didn’t  plug  well  or 

broken handle wire

 

Check and connect the wire well or change handle 

wire.

 

B. Broken  wire  of 

console 

Change the console 

Console 

incomplete 

display 

or 

lack 

of 

strokes

 

A. Loose  screw  of 

display board 

Tighten the screw 

B. Broken system 

Change the console 

Содержание GT4.0

























Отзывы: