GUTMANN mega macs 42 SE Bike Скачать руководство пользователя страница 28

Страница: 28 / 53

Configuring the Device

mega macs 42 SE Bike

Configuring the Car History

2. Select and confirm

Self-test

under

> Settings

in the main menu.

CAUTION

Rolling of vehicle

Risk of injury or material damage

Proceed as follows before starting:

1. Prevent the vehicle from rolling.

2. No gear is engaged.

3. Regard the window with infos and instructions.

NOTICE

Short circuit and voltage peaks when connecting the DT VCI

Danger of destruction of automotive electronics

Switch off ignition before connecting the DT VCI to the vehicle.

3. Insert the DT VCI into the vehicle's diagnostic connector.

Both LEDs of the DT VCI flash. The DT VCI is ready for operation.

4. Select and confirm

>VCI diagnostics<

The

Bluetooth® diagnostics

window appears.

The Bluetooth® function is being tested.

VCI diagnostics is completed successfully if

is displayed under

Defective protocols

and

Diagnostics complete

displayed under

Status

6.11

Configuring the Car History

This menu provides the diagnostic results to the present vehicle from the functions

>Trouble codes<

>Parameters<

>Basic settings<

and

>Codings

. This has the following advantages:

•

You can evaluate the diagnostic results later.

•

Compare previously performed diagnostics to present diagnostic results.

•

You can show the customer the diagnostic results without needing to reconnect the vehicle.

6.11.1 Deleting Entries from the Car History

Proceed as follows to delete entries from the Car History:

1. Select and confirm

>Car History<

in the main menu.

2. Select the requested vehicle.

3. Select and confirm

4. Select and confirm

>Delete<

A confirmation message appears.

5. Observe the confirmation prompt.

6. Affirm the confirmation message with

ENTER

. Abort the procedure with

ESC

The selected entry will be deleted.

Содержание mega macs 42 SE Bike






















































Результаты поиска

Содержание mega macs 42 SE Bike

Отзывы:

Похожие инструкции для mega macs 42 SE Bike

Бренды по названию

Популярные бренды

GUTMANN mega macs 42 SE Bike, Руководство пользователя

Результаты поиска

Содержание mega macs 42 SE Bike

Отзывы:

Похожие инструкции для mega macs 42 SE Bike

Бренды по названию

Популярные бренды