manualshive.com logo in svg

Guthrie Douglas TESS 308, Руководство по установке

Поделиться
Скачать
Guthrie Douglas TESS 308 Скачать руководство пользователя страница 2

Tess 308 Installation Manual – Issue 1 (DR1004, July 2014)                                                           Page | 2  
 

Contents 

 

1. Important information about TESS Systems ....................................................................................... 3

 

2. Tess 308 System..................................................................................................................................4 

3. Fitting Kit ............................................................................................................................................. 5

 

4. System Preparation - Fabric fitting if not pre fitted  ..........................................................................6 

5. Installation..........................................................................................................................................7 

6. Hirschmann Fitting ............................................................................................................................ 12 

7. Manual Motor Limits Setting ............................................................................................................ 13 

8. Radio Motor Limits Setting ............................................................................................................... 14 

9. Maintenance ..................................................................................................................................... 16 

 

 

 

 

Содержание TESS 308


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды