manualshive.com logo in svg

Gulfstream GS A-Class 12/OV, Инструкции по проектированию, установке и обслуживанию

Gulfstream GS A-Class 12/OV - Инструкции по дизайну, установке и обслуживанию. Скачайте бесплатно руководство по эксплуатации с manualshive.com. Этот мануал поможет вам разобраться с продуктом и правильно установить его для максимальной эффективности.

Поделиться
Скачать
background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

Page 20

4.2   ELECTRICAL WIRING
The standard models are supplied with factory fitted single channel heating and hot 
water programmer. Therefore only a room thermostat is required to be supplied and 
wired to the appliannce.

However, other system controls e.g. 2-channel remote programmer, programmable 
room thermostat can be connected to the appliance and for this, the appliance model 
with no clock option should be ordered.

4.2.1   General
(a)  WARNING:  This  appliance  MUST  BE 

EARTHED. 

(b)  The wiring must comply with the current 

I.E.E Requirements for Electrical Installations 
(BS 7671) and the requirements of the local 
electricity utilities.

(c)  It  is  the  responsibility  of  the  competent 

electrical installer to use the details in this 
manual with the latest British Standards. 

(d)  The  appliance  has  integral  9kW  electric 

backup  boiler  and  therefore  the  supply 
must  be  230V~,  50Hz  rated  at  45A  as 
discussed below in table 4.4.

(e)  All electrical wiring to the appliance should 

be  secured  to  prevent  the  wires/cables 
touching  any  hot  surfaces  inside  and 
outside the appliance case.

(f)  The  appliance  is  supplied  with  2m  long, 

10mm

2

 (twin + E) flexible cable and it must 

be connected to a local (not more than 2m 
away from the appliance) 45A double pole 
isolator having a contact separation of at 
least 3mm in both poles as shown in figure 
4.5.

4.2.2      Connecting  Power  Supply  to  the 

Appliance

(a)  Ensure that the electricity supply is switched 

off. 

(b)  The  appliance  is  supplied  with  2m  long 

10mm

2

  (twin  +  E)  flex.  Uncoil  this  and 

connect it to the local fixed isolator (figures 
1.1. 1.2 and 4.5).

(c)  DO NOT SWITCH ON the electricity supply 

to the appliance at this stage.

Figure 4.4A Appliance wiring panel with factory fitted Programmer

Table 4.4 Wiring specification and general guide for all models

Rating @ 230V~ 50Hz
Note:  All models are fitted with 9kW electric 
backup boiler

9.0kW, 41.3A

Power  consumption  when  gas  boiler  is 
operating @ 230V~ 50Hz

Model 12: 205W, 0.9A
Model 20: 216W, 1.0A
Model 30: 248W 1.1A

Minimum rating of isolating switch

45A @ 250V ~ 50Hz

Maximum  cable  run  based  on  a  9.2  volt 
drop  &  earth  fault  loop  impedance  for  0.4s 
disconnection  time,  when  using  type  B 
protection device to BS EN 60898

10mm2 cable: 45m

9.3kW  appliance  -  Recommended  circuit 
protection  device  (CPD)  to  ensure  0.4s 
disconnection time under fault conditions
* Provides best protection

45A type 1 mcb to BS 3871
45A type B circuit breaker to BS EN 60898*
50A type 1 mcb to BS 3871
50A type B circuit breaker to BS EN 60898

4.2.3   Room Thermostat (Standard Models)

 

The  standard  GulfStream  models  are 
supplied with factory fitted and wired single 
channel  programmer  for  controlling  the 
hot  water  and  space  heating  on-off  time 
periods. This appliance is only suitable for 
connecting  230V,  50Hz  i.e.  mains  voltage 
room thermostats.

(a)  Remove link L1 from terminals labelled ‘L-R’ 

and ‘SL-h2’ (see figures 4.4A).

(b)  Wire the room thermostat to the appliance 

terminals as shown in figure 4.6

INSTALLATION AND WIRING

�

�����

����

�����

���

���

�

�

�

��

��

����

���

���

����

����

��

�

���������������

������������

�

�

��

������������������������������������������
������������������������������������������
������������������������������������������
�������������������������������������
���������������������������

�������

�

����������������������������

������������

����������������

�����������������������������������������������������������������

�

��������������

����������

Figure 4.4B Appliance wiring panel with NO clock option

�

�����

����

�����

���

���

�

�

�

��

��

����

���

���

����

����

��

�

���������������

������������

�

�

��

��

��

������������������������������������������
������������������������������������������
������������������������������������������
�������������������������������������
���������������������������

�������

�

����������������������������

������������

����������������

�������������������������������������������������������

�

Содержание GS A-Class 12/OV













































Отзывы:

Нет отзывов

Похожие инструкции для GS A-Class 12/OV

Nibe ES -160 Installation And Maintenance Instructions Manual preview
ES -160
Бренд: Nibe Страницы: 28
U.S. Boiler Company ALTA-080 Installation, Operating And Service Instructions preview
ALTA-080
Бренд: U.S. Boiler Company Страницы: 104
STIEBEL ELTRON EBK 5 G Operation And Installation preview
EBK 5 G
Бренд: STIEBEL ELTRON Страницы: 60
Excel HE C24 User Manual preview
HE C24
Бренд: Excel Страницы: 65
PEERLESS PUREFIRE PFW-199 Installation, Operation & Maintenance Manual preview
PUREFIRE PFW-199
Бренд: PEERLESS Страницы: 81
Weil-McLain ULTRA Ultra-105 Service Manual preview
ULTRA Ultra-105
Бренд: Weil-McLain Страницы: 60
Cecilware ME10-GN Operation Manual preview
ME10-GN
Бренд: Cecilware Страницы: 11
Gorenje ECO HEAT 10 CA II PLUS User And Installation Manual preview
ECO HEAT 10 CA II PLUS
Бренд: Gorenje Страницы: 74
Alpha Boilers SY9-24 Installation And Servicing Instructions preview
SY9-24
Бренд: Alpha Boilers Страницы: 32
Gorenje TC 100 ZNT Manual preview
TC 100 ZNT
Бренд: Gorenje Страницы: 36
Beretta POWER MAX 100 Installation And Operation Manual preview
POWER MAX 100
Бренд: Beretta Страницы: 60
Biodom 33 Instructions For Use, Maintenance And Installation Manual preview
33
Бренд: Biodom Страницы: 61
Harman Stove Company PB 105 Installation & Operating Manual preview
PB 105
Бренд: Harman Stove Company Страницы: 40
Potterton BOA 68 Maintenance Manual preview
BOA 68
Бренд: Potterton Страницы: 5
Potterton 7668920 Engineer'S Service Manual preview
7668920
Бренд: Potterton Страницы: 20
Potterton Powermax HE 85 User Instructions preview
Powermax HE 85
Бренд: Potterton Страницы: 8
Viessmann VITOCONTROL-S, WB2B Service Instructions Manual preview
VITOCONTROL-S, WB2B
Бренд: Viessmann Страницы: 124
THERMEx Antares HM 24 Installation And User Manual preview
Antares HM 24
Бренд: THERMEx Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды