background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

Page 10

2.2   HOT WATER PERFORMANCE
This  appliance  has  hot  water  priority 
control  logic  and  the  hot  water  storage 
vessel is directly heated by the boiler and 
therefore  full  boiler  output  is  used  for 
heating hot water resulting in very short 
recovery times. Typical recovery times for 
raising  the  stored  water  temperature  by 
45

o

C for models ‘-12’, ‘-20’, ‘-30’ are 25, 15 

and 10 minutes respectively. 

The  hot  water  performance  of  the 
appliance is shown in fi gure 2.2. The fl ow 
rates  and  the  corresponding  maximum 
hot water volumes drawn off and quoted 
in table 2.2 and fi gure 2.2 assume adequate 
dynamic pressure and fl ow to property and 
the store is charged to design temperature 
of 75

o

C. 

The mixed fl ow temperature will provide 
a 35

o

C rise when water is drawn off at up 

to 35 l/min as shown in fi gure 2.2 provided 
the  maximum  water  volume  is  not 
exceeded.  At  nominal  35

o

C  temperature 

rise, the maximum hot water production 
of the models ‘-12’, ‘-20’ and ‘-30’ is 400, 560 
and 770 litres per hour respectively.

2.3   SPACE HEATING PERFORMANCE
All models modulate down to about 10kW 
heat output without burner cycling and if 
the demand is below this level, the burner 
will cycle to match the heat demand.

GulfStream

A-CLASS

  has ‘hot  water  priority’ 

controls  and  therefore  full  boiler  output 
is  available  for  space  heating  i.e.  no 
allowance  is  necessary  for  domestic  hot 
water load when selecting the appliance. 

All GulfStream

A-CLASS

 models are fi tted with 

Grundfos UPR 15-50  modulating pumps 
as standard.  The net pump head available 
for space heating circuit is shown below 
in fi gure 2.3.

All  models  are  factory  fitted  with  an 
automatic  bypass  valve  and  is  factory 
set  to  operate  at  a  differential  pressure 
of 2.5m head. 

For  optimum  performance,  this  valve 
must be set during commissioning to suit 
the heating system. The characteristic of 
the  automatic  bypass  valve  is  shown  in 
fi gure 2.4.

TECHNICAL DATA

0

5

10

15

20

25

30

35

0

100

200

300

400

500

600

700

800

900

1000

model - 12
model - 20
model - 30

Figure 2.2 Hot water performance of GulfStream

A-CLASS

models

(Volumes for 35

o

C temperature rise and 10

o

C mains inlet temperature)

Hot Water Flow Rate (1/min)

D

ra

w-off

Volume

(litr

es)

100

200

300

400

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Figure 2.4 Characteristics of the automatic bypass valve

2,43

2,56

2,85

3,24

3,81

Kvs

P(bar)

Q (l/h)

0,1

0,5

�����������������������������������������������������������

�������

����

����

����

����

����

����

����

����

����

����

����

���

���

���

���

���

���

���

���

���

���

�����������������

�������������������������������

�����������������������������������������������

��

��

��

��

��

Содержание GS A-Class 12/OV













































Отзывы: