Guilin Woodpecker Medical Instrument CURING LIGHT LED.C Скачать руководство пользователя страница 3

Страница: 3 / 24

1. Introduction

Guilin Woodpecker Medical Instrument Co., Ltd. is a high-

tech enterprise in researching, developing, and producing dental

equipment, and has a perfect quality assurance system, main

products including ultrasonic scaler, curing light, micro motor,
apex locator and ultrasurgery etc.

2. Principle and usage

2.1 LED.C adopts the principle of ray radiation to solidify the

light-sensitive resin by shooting at it in a short time.

2.2 This product is used to restore teeth and solidify material

for whitening teeth.

3. Structure and components

LED.C (dental) is composed mainly of high power LED,

optical fiber and main unit. (Picture 1)

4. Technical specifications

4.1 Power supply:

Rechargeable Lithium battery

Battery model: ICR18490

Battery voltage and capacity: 1400mAh

Input of adapter: 100V to 240V~ 50Hz/60Hz

Built-in fuse of adapter: 1A/250V

4.2 Applied part: optical fiber

4.3 Light source:

Wavelength: 385nm-515nm(wide-spectrum) / 420-480nm

(Please refer to the label to see if this curing light is wide-

specturm).

Light intensity: 1000mW/cm2~1200mW/cm2

Содержание CURING LIGHT LED.C

























Результаты поиска

Содержание CURING LIGHT LED.C

Отзывы:

Бренды по названию

Популярные бренды

Guilin Woodpecker Medical Instrument CURING LIGHT LED.C, Руководство пользователя

Результаты поиска

Содержание CURING LIGHT LED.C

Отзывы:

Бренды по названию

Популярные бренды