Guildline 9211B Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 35

Guildline 9211B Series Скачать руководство пользователя страница 31

Section 5

TM9211B-A-00

6 November 2013

5-2

5.2.1.7

Readout instrument should indicate and be stable when tested in another circuit in

accordance with the manufacturer's instructions.

5.2.1.8

Power source should be tested for output. If no output, troubleshoot in accordance with

manufacturer's instructions.

Note:   A skipping or variable rheostat in the circuit can cause results similar to a broken lead or bad
connnection.

5.2.2

Short Circuit Troubleshooting

If a short circuit is found in the instrument, check as follows:

5.2.2.1

Verify proper connection of all leads

5.2.2.2

Physical condition of vented rear cover. If cover indented badly, it could short circuit

two or more resistors by touching them.  Remove the cover from the rear panel taking care not to
put  pressure  on  any  resistors.    Straighten  the  cover.    Examine  the  internal  circuit  visually  for
possible snorting of components. Reinstall the cover observing the same precautions.

5.2.2.3

Compare each resistor to a standard resistor

5.2.2.4

If tests above are negative, the problem may be in the internal wiring or resistors in

the  shunt.  Each  shunt can  be  tested  separately  for continuity  without  removing  the  rear  vented
cover,  by  inserting  the  two  plugs  in  the  paired  female  receptacles  for  each  range  and  using  an
ohmmeter between the "10 A MAX." or "100 A MAX" or "300 A MAX" binding post and the "Input
Common"  binding  post.  If  a  defective  shunt  or  internal  connection  is  found  (or  suspected),  the
entire  unit  should  be  returned  for  possible  repair.  (See  Warranty  information  in  front  of  this
manual for instructions).

5.3

Replaceable Parts

The following tables list the replaceable parts.

Note that once a part has been replaced, the unit

will require to be recalibrated.

To Contact Guildline Instruments, the following information is provided.

USA and Canada Telephone: (613) 283-3000
USA and Canada Fax: 1-613-283-6082

Outside US and Canada Telephone: +[1] 613 283-3000
Outside US and Canada Fax: [1] +613 283-6082

You can also contact Guildline Instruments Limted via their Email or Websites.

Email is:

[email protected]

Website is:

www.guildlinecom

«
...
29
30
31
32
33
...
»

Содержание 9211B Series




































Отзывы:

Нет отзывов