background image

 

Safety and Compliance User Notices 

 

This GPR-device is certified according to FCC, subpart 15, IC RSS-220 and ETSI EN 

302 066-1&2. 

 

 You are cautioned that changes or modifications not expressly approved by the party 
responsible for compliance could void the user’s authority to operate the equipment. 

 

NOTE: This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the 

following measures: —Reorient or relocate the receiving antenna. —Increase the 

separation between the equipment and receiver. —Connect the equipment into an 

outlet on a circuit different from that to which the receiver is connected. —Consult the 

dealer or an experienced radio/TV technician for help. 
 

According to the regulations stated in ETSI EN 302 066-1 (European 
Telecommunication Standards Institute): 

The control unit should not be left ON when leaving the system unattended. It should always be 

turned OFF when not in use. 
 

The antennas should point towards the ground, walls etc. during measurement and not towards 

the air. 

 

The antennas should be kept in close proximity to the media under investigation. 

 

Canadian and US regulations state that whenever GPR antennas are in use 
the following notes apply: 

This Ground Penetrating Radar device shall be operated only when in contact with or within 1 

m of the ground. 

 

Only law enforcement agencies, scientific research institutes, commercial mining companies, 

construction companies and emergency rescue or firefighting organizations shall use this 

Ground Penetrating Radar Device. 

 

This device complies with Industry Canada license-exempt RSS standards. Operation is subject 

to the following two conditions: (1) This device may not cause interference and (2) this device 
must accept any interference, including interference that may cause undesired operation of the 

device. 

 

 

Содержание MALA MIRA HDR




















Отзывы: