7
To work outdoor use special extension
cables, be sure it is appropriate for this
purpose and properly marked.
Be aware. Watch out what you are doing.
Use common sense. Never use power
tools if tired.
Always check for damaged parts before
use. In case of light damage think
seriously if the tool will work properly and
safely in such condition. Check all
moving parts for proper alignment. Do
they match? Are the parts damaged? Are
they mounted together properly? Are all
requirements met, to run it perfectly?
Repair or replace all damaged guards, if
not stated otherwise in the instruction
manual. Damaged switch must be
replaced in a specialized workshop. Never
use the tool if it cannot be turned on and
off by proper switch. If the table insert is
worn out, replace it. If you find any defect
on the tool (including safety guards and
saw blade) contact local Service center.
To reduce risk of electric shock, don’t
touch any grounded objects with your
body, e.g. water piping, radiators, cookers
and fridges.
When servicing or maintaining the tool,
use only authorized replacement parts.
Get the replacement parts from
authorized Service center
Never use accessories that are not
recommended in the instruction manual. It
can lead to personal injury and property
damage.
Always use feeding adapter for the
workpiece.
Safety instructions for the first
start up.
Plug the cord out of receptacle before the
adjustment or maintenance.
Rotating blade can cause bodily harm; it can
cut off your fingers.
Never operate the tool without saw blade
guard.
Before start of the tool ensure that data on
the product label match with the parameters
of the power supply.
When using extension cord, ensure that the
wire diameter is sufficient for the stated input.
It must be minimum 1,0 mm
2
.
Keep the tool table and whole working area
clean and tidy, remove all objects you are not
going to need.
Watch out for the obstacles around the tool
you could trip over, like power cord.
Person operating the tool should not be
disturbed.
Check the rotation direction of the motor and
saw blade match together.
Never try to stop rotating saw blade by
pressing your hand, after you turned it off.
Always use perfect blades only, well sharp,
cracks and deformation free. Replace faulty
blades immediately.
Ensure that the arrow on the blade and the
motor show the same direction.
Never remove any safety equipment form the
tool.
Damaged safety equipment has to be
replaced immediately.
If disturbed while working with the tool, first
stop the work you are doing than lift up your
eyes.
Workpiece must stay on the tool table. Never
have it out of the table if you want to cut it.
Always keep your hands in safe position, so
they cannot slide and touch the blade.
If working with workpiece that overhang the
table use an outboard stand to provide
support. So the tool will not cross and chew.
Confirm that the workpiece is free of nails or
other foreign objects. While using the tool
stand always sideway towards the blade.
Never force the tool, because it rotates
slower and is overheating.
Never cut more then one workpiece.
Always use feeding adapter.
Never try to remove any chips or wood
pieces or jammed workpiece before you turn
the tool off and unplug the power cord.
While doing repairs first turn the tool off and
unplug the power cord.
Any adjustment, measuring, cleaning, etc.
can be done after you turn the tool off and
unplug the power cord.
Never leave the workplace unattended when
the motor is running and the power cord is
plugged in the receptacle.
Confirm all safety gear of the tool is well
mounted back after doing maintenance.
It is necessary to know all safety rules in
force on the workplace.
In confined places you must use the dust
sucking unit.
This table, bevel slide miter saw should be
connected to 230 V/16A power source.
Use the power cord only for designed
purpose.
Confirm proper footing and balance while
working.
Always check the safety equipment of this
tool before use. Check if lightly damaged
parts are working properly.
Always check if all moving parts are working
properly. Particularly check if the parts are
not damaged or jammed. All parts must be
well mounted and work perfectly.
