background image

Note: this is a control system which must be cleaned and maintained on a regular basis (see maintenance guide and record MGRG-1000).

6

Guardian Equipment
1440 N North Branch
Chicago, IL 60642

312 447 8100 

telephone

312 447 8101 

facsimile

gesafety.com

rev. 0114 / © 2014  Guardian Equipment

Installation, Operation and Maintenance Guide

G3600 Series Thermostatic Mixing Valves

Flow Capacities

Maximum flow capacity gallons per minute

Pr

essure drop PSIG

CAUTION: ALL THERMOSTATIC WATER MIXING 

VALVES HAVE LIMITATIONS. THEY WILL NOT PROVIDE 

THE DESIRED ACCURACY OUTSIDE OF THEIR FLOW 

CAPACITY RANGE. CONSULT THE CAPACITY CHART 

AND DO NOT OVERSIZE. MINIMUM FLOW MUST BE 

NO LESS THAN SHOWN BELOW.

IMPORTANT: THESE SYSTEMS ARE DESIGNED TO 

PROVIDE MIXED WATER FROM 60 TO 90°F (15 TO 

32°C) FOR FACE/EYEWASH APPLICATIONS ONLY. CALL 

GUARDIAN EQUIPMENT FOR SYSTEMS DESIGNED 

TO OPERATE AT TEMPERATURES OUTSIDE OF THIS 

RANGE.

Limited Warranty

Guardian Equipment warrants the original purchaser that products manufactured by them, (not by others), will be free from defects in materials and 

workmanship under normal conditions of use. When properly installed and maintained in accordance with Guardian Equipment’s instructions, for a period of one 

year from date of shipment. During this period the Guardian Equipment  will at its option repair or replace any product, or part thereof, which shall be returned, 

freight prepaid, to the Guardian Equipment factory and determined by Guardian Equipment to be defective in materials or workmanship. There are no warranties, 

express or implied, which extend beyond the description contained herein. There are no implied warranties of merchantability or of fitness for a particular 

purpose. In no event will Guardian Equipment be liable for labor or incidental or consequential damages. Any alteration or improper installation or use of the 

product will void this limited warranty.

MODEL IN** OUT**

MINIMUM 

FLOW 

(GPM)

INTERNAL 

COLD WATER 

BYPASS 

MINIMUM

SYSTEM PRESSURE DROP

5

10

15

20

25

30

35

40

45

PSI

L/MIN

.3

.7

1.0

1.4

1.7

2.1

2.4

2.8

3.1

BAR

G3600 1/2"

1/2"

2

4

2.5

4

5

6

7

8

8.5

9.5

10

GPM

7.6

15

9.5

15

19

23

27

30

32

36

38

L/MIN

MAXIMUM FLOW CAPACITY

**G3600 HAS 1/2" NOMINAL SWEAT CONNECTIONS.  

G3650 HAS 3/4" NPT THREADED CONNECTIONS.

G3600 
G3650

Содержание G3600 Series







Отзывы: