background image

38

ACCESSORIES

If you have a question about GTO/PRO accessories 

just call 1-800-543-GATE!

12" Push to Open Bracket (R4KPTO) 

An optional longer Post Pivot Bracket for push-to-open installations that need a greater distance to achieve the 
safe gate and gate operator clearance (2 inches). Order two 12" PTO brackets for conversion of a dual swing gate 
installation.

Column Mount Lock Receiver

 

(433IH) 

For mounting the 

Automatic Gate Lock

 on brick columns, walls, or for other applications with limited space 

between gate and post.

Replacement Transformer (RB570)

Standard 18 volt, 2200 mA, AC transformer for maintaining the battery included with the 

GTO/PRO® 4000XL 

gate 

operator. This is the only transformer approved for use with 

the GTO/PRO® 4000XL 

gate operator systems.

Garage Door Receiver (RB709U) 

The Garage Door Receiver allows you to use the same 

GTO/PRO® 

entry transmitter (see Dual Transmitter) to 

operate your gate operator and your garage door operator. Compatible with most garage door operators.

Wireless Entry Intercom / Keypad (F3100MBC)

Allows owner to screen guest at the gate before allowing access to the property. Keypad also allows owner 
to give up to 25 programmable entry codes to family, friends or approved delivery personnel. Codes can be 
permanent of temporary. Can be wireless up to 500 feet or hard wired up to 1000 feet. Additional base stations 
available (F3101MBC).

Replacement Battery (RB500) 

Standard 12 volt, 7.0 amp-hour, maintenance-free battery for the 

GTO/PRO® 2500, GTO/PRO® 2000XL, 

GTO/PRO® 3000XL, GTO/PRO® 4000XL 

 gate operator systems. This is the only battery approved for use 

with the 

GTO/PRO®  

gate operator systems. Life expectancy is 3-5 years. 

Low Voltage Wire (RB509) 

The 16 gauge, multi-stranded, dual conductor 

Low Voltage Wire

 is for connecting  the AC powered  

transformer, or the 

Solar Panel 

to the control board. Also used for the connection of accessories, such as locks, 

keypads, push buttons and other wired  control devices. This specially designed wire is UV treated, PVC coated 
and ready for direct burial. Available in 50, 100, 250, 500 and 1000 foot rolls.

The contents of all material available on this installation manual are copyrighted by GTO, Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced, 

downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO.  Any reprinting of GTO publications is by permission only. Copyright 

infringement is a violation of federal law. 

 

GTO®, GTO/PRO®, Bulldog® are registered trademarks of GTO, Inc. Professional Access Systems™ is a trademark of GTO, Inc. and are the exclusive property of GTO, Inc. (“GTO”).  

All rights are reserved by GTO, and these marks may not be used, in any for without the prior, written permission of GTO.  

Содержание 4000XL











































Отзывы: