30309466 2 Issue 2.10
Operation
The address, working mode and tone of the flashing
beacon base can be programmed using P-9910B
programmer in field.
Address Programming
Connect the programmer with Terminal 1 and 3 of the
flashing beacon base. Turn on the programmer, enter
the address code (1 to 242), pressing
Program
, the
screen will show a P meaning the address is
programmed. Refer to
P-9910B Hand Held
Programmer Installation and Operation Manual
for
details.
Setting Tone and Working Mode
In standby state of the programmer, entering number 4,
5 and 6 followed by
Clear,
the screen will show 0 .
Pressing
Function
, the screen still shows 0 . Pressing
3 then, the screen shows - . Entering the tone
number, and pressing
Program,
P will show on the
screen, meaning the tone number has been set.
Pressing
Clear
, the screen shows 0 , further
operation can be done. If the tone number falls into
the range of 1 to 16, the flashing beacon base works in
Mode I; if the number falls into the range of 17 to 32, it
works in Mode II; if the number falls into the range of
33-48, it works in Mode III. Numbers outside these
three ranges will not be accepted, in which case, the
number will be defaulted to be 46 .
Application Method
The flashing beacon base can be used as a
detector base to mount intelligent detectors, so that
the detector can carry out both fire detection and
alarm.
It can also be directly connected into fire alarm
system. In case of a fire alarm, it will generate the
pre-set alarm sound.
Caution:
Please read this manual carefully before
operation.
DZ-03 base should be used together with this
product.
A loop can have maximum 30 flashing beacon
bases due to their current consumption.
Please order the special top cover if it s not
connected with fire detector.
Never try to repair it by yourself. Always contact
your distributor in case of any trouble.
Specifications
Operating Voltage
Loop 24V (20V~28V)
Quiescent Current
1mA
Alarm Current
6mA
Mode
Mode I, II & III.
Alarm tones
Optional 16 tones. Please
refer to the table of tones.
Flash indication
Bright red flash, frequency
1Hz
Programming
Electronically programmed
Code Range
1~242
Ingress Protection
Rating
IP21C
Operating
Temperature
-
10 ~
+
50
Relative Humidity
95%, non condensing
Material of
Enclosure
ABS
Dimension
Diameter: 152.4mm
Height: 41.3mm (without
cover)
Mounting Hole
Distance
45mm~80mm
Weight
About 235g
Table of Tones
Accessories and Tools
Model
Name
Remark
P-9910B
Hand
Held
Programmer
Order separately
WEEE Information
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste
in the European Union. For proper
recycling, return this product to your
local supplier upon the purchase of
equivalent new equipment, or dispose of it at
designated collection points.
Limited Warranty
GST
warrants that the product will be free from defects
in design, materials and workmanship during the
warranty period. This warranty shall not apply to any
product that is found to have been improperly installed
or used in any way not in accordance with the
instructions supplied with the product. Anybody,
including the agents, distributors or employees, is not
in the position to amend the contents of this warranty.
Please contact your local distributor for products not
covered by this warranty.
THIS PRODUCT IS NOT APPROVED TO EN54-23
(Beacon Functionality) AND MUST NOT BE USED AS
A VISUAL ALARM DEVICE OR TO PROVIDE A
PRIMARY WARNING NOTIFICATION OF FIRE.
Mode
Tone Description
Sound Level
1m Ahead/24V
dB
I
II III
1 17 33 970Hz
87
2 18 34 800Hz /970Hz @ 2Hz
88
3 19 35 800Hz-970Hz@1Hz
84
4 20 36 970Hz 1s on /1s off
86
5 21 37 970Hz, 0.5s/630Hz,
0.5s
88
6 22 38 500Hz - 1200Hz 0.5s
on×3 / 1.5s off
81
7 23 39 2850Hz, 0.5s on/0.5s
off 3/1.5s off
86
8 24 40 2850Hz 0.4s on/0.3s
off
86
9 25 41 550Hz,0.7s/1000Hz,
0.33s
88
10 26 42 1500Hz -2700Hz
@3Hz
83
11 27 43 2400Hz
76
12 28 44 500Hz -1200Hz
@0.33Hz
85
13 29 45 2400Hz -2900Hz
@9Hz
82
14
*
30 46 2400Hz -2900Hz
@3Hz
92
15 31 47 800Hz-970Hz@3Hz
85
16
*
32 48 500Hz-1200Hz,3.75s
on /0.25s off
85
Pre-alarm 800Hz 1s on/1s off
84
*
EN54 Compliant
