GSi FFI SCR Скачать руководство пользователя страница 4

4

PNEG-1712

 FFI SCR Replacement Kit Instructions

1. Introduction

Read these Instructions before Installation and Operation

FFI SCR Replacement Control Kit

The FFI SCR Replacement Control Kit is a service replacement package for the discontinued woods SCR 
control boards installed on Farm Fans dryers from 1990 to 2007.

The FFI SCR Replacement Kit supersedes previous SCR kits and contains the necessary parts for 
replacing the following SCR control boards:

1. 415-3621-0 SCR CONTROL 1 HP-WOODS W/54

2. 415-4563-3 SCR CONTROL 1/3 HP-WOODS W/54

3. 415-3019-7 SCR CONTROL 3/4 HP-WOODS

4. 415-2302-8 SCR CONTROL 3/4 HP-WOODS W/54

5. SCR-003 SCR CONTROL KIT WOODS

6. 056-1580-2 SCR MOTOR CONTROL-WOODS

Beginning in 1990, the woods SCR board was installed on all new CMS-H, CMS-J and M-Series dryers. 
As of July, 1992, the woods SCR board was installed on all new CF/AB and CF/SA series dryers.

SCR All HP with Vari-Trol (D04-0551)

SCR All HP without Vari-Trol (D04-0552)

CAUTION

To reduce the risk of electrical shock or damage to electrical components, turn
OFF and lock out the main power supply before performing any service or
maintenance work on the dryer.

Part #

Description

Qty

U/M

098-1026-8

Wrapper, Nylon TY - 3-5/8"

1

EA

D03-0013-BRK DIN Rail Mount Single Comp 3.9"

1

EA

D03-0854

Minarik SCR Drive

1

EA

FH-6999

Insulator, 16 Gauge Insulator Crimp

1

EA

HH-1462

Nut, 16 Gauge Wire

2

EA

PNEG-1712

FFI SCR Replacement Kit

1

EA

WR-16BLK

Wire, 16 Gauge Stranded MTW Black

4

FT

WR-18RED

Wire, 18 Gauge Red Stranded 
120-1032-8

3

FT

WR-18WHT

Wire, 18 Gauge White Stranded

3

FT

WR-18YLW

Wire, 18 Gauge Yellow Stranded

3

FT

GT3-0971

24 Volt Power Supply

1

70-0064

3 Amp Time Delay Fuse

2

E300-1003

5 Amp Fuse TD

2

GT3-1065

8 Amp Fuse MDA

2

Part #

Description

Qty

U/M

098-1026-8

Wrapper, Nylon TY - 3-5/8"

1

EA

D03-0013-BRK DIN Rail Mount Single Comp 3.9"

1

EA

D03-0854

Minarik SCR Drive

1

EA

FH-6999

Insulator, 16 Gauge Insulator Crimp

1

EA

HH-1462

Nut, 16 Gauge Wire

2

EA

PNEG-1712

FFI SCR Replacement Kit

1

EA

WR-16BLK

Wire, 16 Gauge Stranded MTW Black

4

FT

WR-18RED

Wire, 18 Gauge Red Stranded 
120-1032-8

3

FT

WR-18WHT

Wire, 18 Gauge White Stranded

3

FT

WR-18YLW

Wire, 18 Gauge Yellow Stranded

3

FT

D03-0805

Touch Control, 12 VDC Power Supply

1

EA

70-0064

3 Amp Time Delay Fuse

2

E300-1003

5 Amp Fuse TD

2

GT3-1065

8 Amp Fuse MDA

2

Содержание FFI SCR













Отзывы: