manualshive.com logo in svg

Grundig GCI-K1577TH, Руководство пользователя

Поделиться
Скачать
Grundig GCI-K1577TH Скачать руководство пользователя страница 88

13. CMS Software Introduction

The Central Management System (CMS) software bundles IP cameras and analogue cameras that are connected 
to the network via the Video Server into one system. Offering powerful functionalities via intuitive interface, it is a 
centralised monitoring solution for your video surveillance equipments.

The GRUNDIG CMS Software gives the user access to monitor multiple IP Cameras and Video Servers, and allows 
the user to monitor simultaneously 16 sites per group (up to 10 groups) within several clicks.

For further information on the CMS software, please refer to the supplied CD.

14. Internet Security Settings

If the ActiveX control installation is blocked, please either set the Internet security level to default or change 
ActiveX controls and plug-in settings.

Internet Security Level : Default

Step 1: Start the Internet Explorer.

 

Step 2: Select <Tools> from the main menu of the browser. Then click on <Internet Options>.

86

English

Содержание GCI-K1577TH





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды