Grundig GCI-K1577TH Скачать руководство пользователя страница 14

Страница: 14 / 100

8. Home Page

In the Home page, there are several function buttons that are specified below.

NOTE: Please note that the function buttons can vary depending on the camera model.

Display Mode (Screen Size Adjustment) :
The display size of the image can be adjusted to x1/2 and full screen.

Digital Zoom Control :
In full screen mode, users can implement digital PTZ by rotating the mouse wheel (for zoom in/out).

Zoom Adjustment :

- Tele/Wide:
Hold the <Tele/Wide> button to implement continuous zoom adjustment.

- Wide Steps/Tele Steps:
Clicking on the <Tele/Wide Steps> buttons will lead to the zoom being shifted toward the Tele/Wide side in an
user-defined range, which can be selected from the drop-down menu.

- Reset:
Clicking on the <Reset> button will calibrate the camera lens to the full wide end.

English

Содержание GCI-K1577TH





































































































Результаты поиска

Содержание GCI-K1577TH

Отзывы:

Бренды по названию

Популярные бренды

Grundig GCI-K1577TH, Руководство пользователя

Результаты поиска

Содержание GCI-K1577TH

Отзывы:

Бренды по названию

Популярные бренды