Grundig 43 VLE 5523 BN, Инструкция пользователя

Страница: 64 / 82

ENGLISH
64­
Antenna­settings,­SCR­system­
and­searching­for­digital­chan-
nels­from­a­satellite­automati-
cally
Notes:
7
Your TV supports SCR system (Single Chan-
nel Router – EN 50494).
7
The following description about the LNB set-
tings premise a substantial expertise about
the satellite systems. Ask your specialist
dealer.
1­ Open the menu with » MENU «.
2­
Select the menu item »SOURCE SETUP«
with »
V
« or »
Λ
« and press »
OK
« to
confirm.
3­
Select the line »Source« with »
V
« or »
Λ
«
and press »
OK
« to confirm.
Select the input source »Satellite« with »
<
«,
»
>
«, »
V
« or »
Λ
« and press »
OK
« to
confirm.
4­ Select the line »Antenna Settings« with »
V
«
or »
Λ
« and press » OK « to confirm.
– The menu appears.
5­ Select and set the required option for the
antenna settings with »
V
« or »
Λ
«:
­ Satellite­
Press »
OK
« then select the required satel-lite
with »
<
«, »
>
«, »
V
« or »
Λ
« and press
»
OK
« to confirm.
­ LNB­Type­
If your antenna system is equipped with a
single-cable system multiswitch, use the op-
tion »Grundig SCR«. Press » OK « and select
the »Grundig SCR« option with »
<
« or »
>
«.
Select the »LNB-Frequency High« line with
»
V
« and enter the frequency with » 1...0 «
in five digits.
Select the »LNB-Frequency Low« line with
»
V
« and enter the frequency with » 1...0 «
in five digits.
Confirm the settings with »

« (green).
­ User­Band­
Select the number of the antenna socket
used with »
<
« or »
>
«.
SETTING­FURTHER­CHANNELS
­-----------------------------------------------------
­ UB­Frequency­(MHz)­
Enter the required frequency for the selected
antenna socket with » 1...0 «.
­ LNB­Selection­
Depending on the number of LNBs, select
the option with »
<
« or »
>
«.
1/2« if only 1 LNB is used; if two LNBs are
used, select the required LNB (»1/2« or
»2/2«).
Notes:
7
Use installation equipment supported / sug-
gested by your SCR Switch.
7
Other users / receivers connected to the
system may be affected if the specified user
band number and frequency is changed
during installation.
7
User band and user band frequency is
specified on the SCR switch used; and each
user / receiver must select a specified user
band and user band frequency.
7
With SCR satellite system, auto search by
several users / receivers at the same time
may cause problems.
6­ Select »Auto Tuning« by presing »

« (red).
7­ Select the line »Scan Mode« with »
V
« or
»
Λ
«.
Select the scan mode with »
<
« or »
>
«
(for unencrypted channels, for encrypted
channels only, or both).
8­
Select the line »Service Type« with »
V
« or
»
Λ
«.
Use »
<
« or »
>
« to select whether you want
to search for television channels (TV) only,
radio stations only (Radio) or both
(Radio + TV).
9­ Start the scan with »

« (red).
– The »Results« menu appears, and the scan
for TV channels begins.