background image

English (GB)

11

4.13 Installing the venting pipe

If the cover is not pre-installed with a venting pipe, we 
recommend that you provide the pit with a venting pipe, supplied 
as an accessory.
For installation, see section 

4.6 Connecting the pipes

.

Fig. 21

Pit with venting pipe

4.14 Installing the cable entry

The cables to the level switches and the pump can be led into the 
pit through a cable entry in the side of the upper region of the pit. 
See fig. 

22

.

Fig. 22

Pipe for cable entry

5. Installing the level controllers

When installing the level controllers, observe the following points: 
• To prevent air intake and vibrations in the pump, install the 

stop level switch in such a way that the pump stops before air 
is sucked into the pump.

• In the case of 1-pump operation, install the start level switch in 

such a way that the pump starts at the required level; however, 
start the pump before the liquid level reaches the lower edge 
of the bottom inlet pipe.

• In the case of 2-pump operation, install the start level switches 

in such a way that pump 2 starts before the liquid level 
reaches the lower edge of the bottom inlet pipe, and so that 
pump 1 starts correspondingly earlier.

• Install the high-level alarm switch about 10 cm above the start 

level switch; however, the alarm must always be given before 
the liquid level reaches the inlet pipe. 

For further settings, see the installation and operating instructions 
for the pump controller selected.

5.1 Start and stop levels

The effective volume of the pit must be so large that the number 
of starts does not exceed the maximum permissible number. See 
the installation and operating instructions for the pump.

5.2 Installing the pump controller

See the installation and operating instructions for the pump 
controller.

TM0

6

 3

91

3 1

2

1

5

TM

06

 34

7

8

 06

15

Adjust the length of the power cable by coiling it up 
on a relief fitting to ensure that the cable is not 
damaged during operation.
Fasten the relief fitting to a suitable hook at the top of 
the pit.
Make sure that the cable is not sharply bent or 
pinched.

If the pit is equipped with an Auto

ADAPT

-controlled 

pump, an external level controller is not needed.

Check that the pump controller is designed for the 
pumps to be installed.

Содержание PS.W.04



































Отзывы: