background image

19

3.1 

Cable end to motor

Fit plug pins on the black, blue and brown leads. See fig. 7.

Press home the plug pin and fix it firmly by means of the crimping tool, part 

no. SV 03 74. See fig. 8.

Fit the cable in the motor. See 2. Replacement of motor cable.

3.2 

Checking of direction of rotation

Observe the movement of the pump shaft when the electricity supply is 

switched on for a short period. The correct direction of rotation is indicated 

by an arrow on the side of the motor.

Fit the fittings and the hose to the pump. The pump is now reassembled and 

can be tested.

 

Fig. 7  Fit plug pins

Fig. 8  Fixing the plug pin

Fig. 9  Checking direction of

  rotation

Disclaimer 

Nothing from this document may be copied and/or made public by means of printing, photocopy, microfilm or in any other way without 

the prior written approval of the publisher. Technical data can change without prior notification. Eijkelkamp Soil & Water is not responsible 

and/or liable for any damage and/or personal injury due to (incorrect) use of this product. Eijkelkamp Soil & Water would be pleased to 

receive your reactions and comments about this product and the user instructions. 

Содержание MP 1 / Redi-Flo2




















Отзывы: