Grundfos MP 1 / Redi-Flo2 Скачать руководство пользователя страница 3

Страница: 3 / 19

Information on this manual

If the text follows a mark (as shown on the left), this means that an important instruction follows.

If the text follows a mark (as shown on the left), this means that an important warning follows

relating to danger to the user or damage to the apparatus. The user is always responsible for its

own personal protection.

Italic indicated text indicates that the text concerned appears in writing on the display or the

apparatus (or must be typed).

General description

Prior to installation, read these installation and operating instructions (also read the separate

manual on the frequency converter). Installation and operation must comply with local regulations

and accepted codes of good practice.

The Grundfos MP 1/Redi-Flo2 submersible pump is specially designed for the purging and sampling of

contaminated groundwater in boreholes with an internal diameter of at least 50 mm. The pump is powered

via an adjustable converter in the 25 to 400 Hz frequency range. At 400 Hz, the pump provides a flow rate of

1 m

/h at 74 metres head.

The pump must always be powered via the converter. See fig. 1.

Pump and converter (motor) form a complete unit that can easily be dismantled for cleaning and servicing.

The Teflon power cable is available in different lengths.

2.1 Applications

The Grundfos MP 1/Redi-Flo2 pump is designed for the purging and sampling of contaminated water. The

maximum sand content of the water must not exceed 50 g/m

. A larger sand content will reduce the life of the

service parts and increase the risk of blocking of the pump. Water temperature: +1 °C to +30 °C.

All pump components are made from materials not giving off foreign matter to the pumped liquid except

PFOS/PFOA. If you are going to sample for these parameters, please ask your distributor how to act. For other

contaminants the sample taken is not influenced nor altered by the pump.

To avoid cleaning the pump and to eliminate the risk of cross-contamination, permanent installation of the

pump is recommended.



Text

Fig. 1 Submersible pump Grundfos MP 1/Redi-Flo2 and

frequency

converter

Содержание MP 1 / Redi-Flo2




















Результаты поиска

Содержание MP 1 / Redi-Flo2

Отзывы:

Похожие инструкции для MP 1 / Redi-Flo2

Бренды по названию

Популярные бренды

Grundfos MP 1 / Redi-Flo2, Руководство пользователя

Результаты поиска

Содержание MP 1 / Redi-Flo2

Отзывы:

Похожие инструкции для MP 1 / Redi-Flo2

Бренды по названию

Популярные бренды