Grundfos MP 1 / Redi-Flo2 Скачать руководство пользователя страница 4

Страница: 4 / 19

It is possible to use the same pump for sampling in several boreholes if the risk of cross-contamination can

be eliminated.

The MP 1/Redi-Flo2 pump is not designed for the pumping of concentrated oils, chemicals or explosive

liquids.

When pumping liquids with a density or kinematic viscosity higher than that of water, a motor input power

higher than the rated power is required. The maximum performance must therefore be reduced by changing

the frequency.

When the MP 1/Redi-Flo2 pump is used, the regulations covering the handling of hazardous material

and possible local regulations must be observed.

The MP 1/Redi-Flo2 pump is not designed for continuous operation like for instance remedial pumping.

Continuous operation may reduce the life of the pump.

2.2

Technical specifications

Marking:

The MP 1/Redi-Flo2 sampling pump system is CE-marked.

Submersible pump Grundfos MP 1/Redi-Flo2:

Power input:

1.3 kW

Voltage:

3 x 220 V, 400 Hz

Maximum current:

5.5 A

Motor protection:

Built-in thermal switch

Water temperature:

0 °C to +35 °C

Discharge port:

Rp 3/4

Continuous operation:

Maximum 500 hours

Net weight:

2.5 kg

Frequency converters:

Supply voltage:

1 x 200-240 V (+/- 10%), 50/60 Hz

Minimum generator size:

With voltage control:

• 3.0 kVA (suitable for non-linear loads, minimal value)

• 4.5 kVA (suitable for non-linear loads, recommended value)

• 7.5 kVA (not suitable for non-linear loads)

Nominal input current:

12.9 A

Nominal output current:

7.0 A

Supply voltage:

1 x 110-115 V (+/- 10%), 50/60 Hz

Minimum generator size:

With voltage control:

• 2.2 kVA (suitable for non-linear loads, minimal value)

• 3.3 kVA (suitable for non-linear loads, recommended value)

• 5.5 kVA (not suitable for non-linear loads)

Nominal input current:

21.9 A

Nominal output current:

5.8 A

Fuse:

10 A

Power factor:

0.65

Connecting cable:

3 x 1.5 mm

, 3 m with plug.

Output voltage:

3 x 15.4 V, 25 Hz, to 3 x 235 V, 400 Hz

Motor protection:

Built-in overcurrent protection, set to 6.1 A

Acceleration time:

0 to 400 Hz: Maximum 6 sec

Deceleration time:

400 to 0 Hz: Maximum 6 sec

Enclosure class:

IP66

Ambient temperature:

–10 °C to +40 °C

Relative air humidity:

Maximum 95 %

Weight:

8.0 kg (incl. case).



Содержание MP 1 / Redi-Flo2




















Результаты поиска

Содержание MP 1 / Redi-Flo2

Отзывы:

Похожие инструкции для MP 1 / Redi-Flo2

Бренды по названию

Популярные бренды

Grundfos MP 1 / Redi-Flo2, Руководство пользователя

Результаты поиска

Содержание MP 1 / Redi-Flo2

Отзывы:

Похожие инструкции для MP 1 / Redi-Flo2

Бренды по названию

Популярные бренды