manualshive.com logo in svg

Grundfos LS 100-80-241, Инструкция по эксплуатации

"Grundfos LS 100-80-241" - надежный насос высокого давления, предназначенный для широкого спектра промышленных и коммерческих приложений. Подробные инструкции по обслуживанию и ремонту можно бесплатно скачать с нашего веб-сайта. Убедитесь, что ваш насос всегда работает на максимуме своих возможностей.

Поделиться
Скачать
background image

English (GB)

10

4.3.2 LS without sleeve, construction type 2

The position numbers in the following refer to section 

9.6 LS 

without sleeve, construction type 2

 on page 25.

Removing the motor

1. Remove the coupling guard.
2. Remove the screws and nuts from the coupling halves.
3. Carefully loosen and remove the spring using a screwdriver.
4. Remove the screws holding the motor on the base frame.
5. Lift off the motor.
6. Loosen the set screws in the coupling flange of the pump.
7. Pull the coupling flange off the pump shaft using a puller.

Removing the bearings and shaft seals, non-drive end

1. Remove the four screws (114a) holding the bearing cover 

(113d).

2. Remove the bearing cover (113d) and gasket (113e).
3. Loosen the round nut (54e). Remove the round nut (54e) and 

the washer (54c) from the shaft non-drive end.

4. Remove the screws (114b).
5. Loosen the bearing housing (113) using expansion bolts.
6. Pull the bearing housing (113) off the shaft (51).
7. Pull the bearing (54) and tab washer (54d) out of the bearing 

housing (113).

8. Remove the lip seal (113f). Use a punch, if necessary.
9. Remove the slinger (79).
10. Remove the screws (58a).
11. Remove the seal cover (58).
12. Remove the gasket (110a) or the O-ring (110).
13. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

14. Remove the seal housing screws (114).
15. Loosen the seal housing

 

(124) using expansion bolts.

16. Remove the seal housing (124).
17. Remove the O-ring (109, 109a).
18. Pull the rotary shaft seal part (105) off the shaft (51).

Removing the bearings and shaft seals, drive end

1. Remove the key (11a).
2. Remove the four screws (114a) holding the bearing cover 

(113c).

3. Remove the bearing cover (113c) and gasket (113e).
4. Remove the screws (114b).
5. Loosen the bearing housing (113) using expansion bolts.
6. Pull the bearing housing (113) off the shaft (51).
7. Pull the bearing (54) out of the bearing housing (113).
8. Remove the lip seal (113f). Use a punch, if necessary.
9. Remove the slinger (79).
10. Remove the screws (58a).
11. Remove the seal cover (58).
12. Remove the gasket (110a) or the O-ring (110).
13. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

14. Remove the seal housing screws (114).
15. Loosen the seal housing (124) using expansion bolts.
16. Remove the seal housing (124).
17. Remove the O-ring (109, 109a).
18. Pull the rotary shaft seal part (105) off the shaft (51).

Removing the upper pump housing

1. Loosen the screws (26c, 26d), and remove them.
2. Fit the screws in the dismounting holes, thereby loosening the 

rest of the pump housing (6a).

3. Lift off the upper pump housing (6a). Use lifting straps on the 

lifting brackets of the pump housing.

4. Remove the screws (26c) from the dismounting holes, and 

then knock up the guide pins so that they are not damaged.

Removing the shaft, impeller and gasket

1. Lift the shaft (51), including the impeller (49) and wear rings 

(45a, 45b or 45c), free of the lower pump housing (6b).

2. Remove the wear rings (45a, 45b or 45c).
3. Remove the snap ring (65) (only pump type LS 200-150-483).
4. Remove the gasket (72a) from the pump housing (6b), and 

clean the packing face.

Removing the impeller

1. Loosen and remove the impeller nut (67b).
2. Push the shaft until the key (11) is free of the impeller (49).
3. Pull the shaft (51) out of the impeller (49), and remove it.

4.4 Assembling the pump, with sleeve

4.4.1 LS with sleeve, construction type 1

Fitting the impeller

1. Fit the shaft (51) in the impeller (49).
2. Fit the impeller nut (67a) on the shaft, and tighten by hand.
3. Centre the shaft in the impeller (49) by measuring from the 

impeller hub to the shoulder on each side of the shaft (51).

4. Tighten the impeller nut (67a).

Fitting the gaskets, impeller and shaft

1. Draw the outline of the old gasket (72a) on a new gasket 

material (gasket thickness 0.8 mm), make holes for the 
staybolts, and coarsely cut out the gasket.

2. Fit the guide screws in the lower pump housing (6b).
3. Fit the gasket (72a), and cut it out.
4. Fit the wear rings (45b) on the impeller (49), and check that 

they can rotate freely.

5. Lift the shaft, impeller and wear rings home in the pump 

housing. Make sure that the pins at the bottom of the pump 
housing engage with the holes of the wear rings.

Содержание LS 100-80-241

















































Отзывы:

Нет отзывов

Похожие инструкции для LS 100-80-241

Dantherm 087353 Installation Manual preview
087353
Бренд: Dantherm Страницы: 12
TradeQuip 2054T Owner'S Manual preview
2054T
Бренд: TradeQuip Страницы: 8
Wilo VeroLine-IPS 20 Installation And Operating Instructions Manual preview
VeroLine-IPS 20
Бренд: Wilo Страницы: 42
Gardena 1489 Operating Instructions Manual preview
1489
Бренд: Gardena Страницы: 10
PerformancePro Cascade Series Owner'S Manual preview
Cascade Series
Бренд: PerformancePro Страницы: 15
Ingersoll-Rand PD05 B Series Operator'S Manual preview
PD05 B Series
Бренд: Ingersoll-Rand Страницы: 12
Atlantic PAF-20SV Product Manual preview
PAF-20SV
Бренд: Atlantic Страницы: 20
Zip HydroTap 30009UK Installation And Operating Instructions Manual preview
HydroTap 30009UK
Бренд: Zip Страницы: 24
SAINT-GOBAIN PFD1 AstiPure Operating Instructions Manual preview
PFD1 AstiPure
Бренд: SAINT-GOBAIN Страницы: 19
XPOtool 63489 User Manual preview
63489
Бренд: XPOtool Страницы: 15
ICP HC4H3 Installation Instructions Manual preview
HC4H3
Бренд: ICP Страницы: 17
NEXT pool STERILOR Cu/Ag Installation Instructions & User Manual preview
STERILOR Cu/Ag
Бренд: NEXT pool Страницы: 19
WATERKOTTE Basic Line BS 7010 Planning And Installation Manual preview
Basic Line BS 7010
Бренд: WATERKOTTE Страницы: 60
Pittsburgh 45743 Owner'S Manual & Safety Instructions preview
45743
Бренд: Pittsburgh Страницы: 4
DAB E-SWIM 150 Manual preview
E-SWIM 150
Бренд: DAB Страницы: 37
Apollo Hydroheat A650YRRTL5 Instruction Manual preview
Hydroheat A650YRRTL5
Бренд: Apollo Страницы: 24
vacuubrand MV 10C VARIO select Instructions For Use Manual preview
MV 10C VARIO select
Бренд: vacuubrand Страницы: 88
Metabo HWW 3000/20 G Operating Instructions Manual preview
HWW 3000/20 G
Бренд: Metabo Страницы: 61

Бренды по названию

Популярные бренды

Загрузить еще бренды