manualshive.com logo in svg

Grundfos LS 100-80-241, Инструкция по эксплуатации

"Grundfos LS 100-80-241" - надежный насос высокого давления, предназначенный для широкого спектра промышленных и коммерческих приложений. Подробные инструкции по обслуживанию и ремонту можно бесплатно скачать с нашего веб-сайта. Убедитесь, что ваш насос всегда работает на максимуме своих возможностей.

Поделиться
Скачать
background image

English (GB)

7

Removing the bearings and shaft seals, non-drive end

1. Remove the four screws (114a) holding the bearing cover 

(113d).

2. Remove the bearing cover (113d) and gasket (113e).
3. Loosen the set screw in the bearing snap ring (54).
4. Loosen the bearing snap ring (54) by moving it against the 

direction of rotation.

5. Remove any marks from the set screws on the shaft non-drive 

end (51).

6. Remove the screws (114).
7. Pull the seal housing

 

(124) off the shaft (51) using a puller, 

and then remove the gasket (109b).

8. Pull the spring, washer and rotary shaft seal part (105) off the 

shaft (51).

9. Pull the bearing (54) out of the seal housing (124).
10. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

Removing the bearings and shaft seals, drive end

1. Remove the key (11a).
2. Remove the four screws (114a) holding the bearing cover 

(113c).

3. Remove the bearing cover (113c) and gasket (113e).
4. Loosen the set screw in the bearing snap ring (53).
5. Loosen the bearing snap ring (53) by moving it against the 

direction of rotation.

6. Remove any marks from the set screws on the shaft drive end 

(51).

7. Remove the screws (114).
8. Pull the seal housing (124) off the shaft (51) using a puller, 

and then remove the gasket (109b).

9. Pull the spring, washer and rotary shaft seal part (105) off the 

shaft (51).

10. Pull the bearing (53) out of the seal housing (124).
11. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

Removing the upper pump housing

1. Loosen the screws (26c), and remove them.
2. Loosen the screws (26d), and remove them (only pump type 

LS 65-50-330).

3. Loosen the upper pump housing by means of a jacking screw 

(inch threads).

4. Lift off the upper pump housing (6a).

Removing the shaft, impeller and gasket

1. Lift the shaft (51), including the impeller (49) and wear rings 

(45b), free of the lower pump housing (6b).

2. Remove the wear rings (45b).
3. Remove the gasket (72a) from the pump housing (6b), and 

clean the packing face.

Removing the impeller

1. Remove the impeller nut (67a).
2. Push the shaft until the key (11) is free of the impeller (49).
3. Pull the shaft (51) out of the impeller (49), and remove it.

4.2.2 LS with sleeve, construction type 2

The position numbers in the following refer to section 

9.2 LS with 

sleeve, construction type 2

 on page 23.

Removing the motor

1. Remove the coupling guard.
2. Remove the screws and nuts from the coupling halves.
3. Carefully loosen and remove the spring using a screwdriver.
4. Remove the screws holding the motor on the base frame.
5. Lift off the motor.
6. Loosen the set screws in the coupling flange of the pump.
7. Pull the coupling flange off the pump shaft using a puller.

Removing the bearings and shaft seals, non-drive end

1. Remove the four screws (114a) holding the bearing cover 

(113d).

2. Remove the bearing cover (113d) and gasket (113e).
3. Loosen the set screw in the bearing snap ring (54).
4. Loosen the bearing snap ring (54) by moving it against the 

direction of rotation.

5. Remove any marks from the set screws on the shaft non-drive 

end (51).

6. Remove the screws (114) or the nuts (36).
7. Pull the seal housing (124) off the shaft (51) using a puller, 

and then remove the slinger (79) and O-ring (109).

8. Pull the spring, washer and rotary shaft seal part (105) off the 

shaft (51).

9. Remove the slinger (79), and then pull the bearing (54) out of 

the seal housing (124).

10. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

Removing the bearings and shaft seals, drive end

1. Remove the key (11a).
2. Remove the four screws (114a) holding the bearing cover 

(113c).

3. Remove the bearing cover (113c) and gasket (113e).
4. Loosen the set screw in the bearing snap ring (53).
5. Loosen the bearing snap ring (53) by moving it against the 

direction of rotation.

6. Remove any marks from the set screws on the shaft drive end 

(51).

7. Remove the screws (114) or the nuts (36).
8. Pull the seal housing (124) off the shaft (51) using a puller, 

and then remove the slinger (79) and O-ring (109).

9. Pull the spring, washer and rotary shaft seal part (105) off the 

shaft (51).

10. Remove the slinger (79), and then pull the bearing (54) out of 

the seal housing (124).

11. Remove the stationary shaft seal part (105). Use a punch, if 

necessary.

Removing the upper pump housing

1. Loosen the screws (26c, 26d), and remove them.
2. Fit the screws (26c) in the dismounting holes, thereby 

loosening the rest of the pump housing (6a).

3. Lift off the upper pump housing (6a).
4. Remove the screws (26c) from the dismounting holes, and 

then knock up the guide pins so that they are not damaged.

Содержание LS 100-80-241

















































Отзывы:

Нет отзывов

Похожие инструкции для LS 100-80-241

Danfoss H1 Series Basic Information preview
H1 Series
Бренд: Danfoss Страницы: 40
Zoeller 57 Series Installation Instructions Manual preview
57 Series
Бренд: Zoeller Страницы: 12
Carrier Infinity 50DT Installation Instructions Manual preview
Infinity 50DT
Бренд: Carrier Страницы: 30
Bayrol Auromatic Salt Instructions For Use Manual preview
Auromatic Salt
Бренд: Bayrol Страницы: 56
Agilent Technologies 969-6500 User Manual preview
969-6500
Бренд: Agilent Technologies Страницы: 306
Power Fist 8519183 User Manual preview
8519183
Бренд: Power Fist Страницы: 20
GORMAN-RUPP PUMPS 2D-X.75 1P Installation, Operation And Maintenance Manual preview
2D-X.75 1P
Бренд: GORMAN-RUPP PUMPS Страницы: 25
Intex 620PC Owner'S Manual preview
620PC
Бренд: Intex Страницы: 5
Zodiac Pac Alpha 5M Instructions For Installtion And Use preview
Pac Alpha 5M
Бренд: Zodiac Страницы: 24
Danfoss RSH Series Installation Manual preview
RSH Series
Бренд: Danfoss Страницы: 4
Garland AMAZON 790 E Instruction Manual preview
AMAZON 790 E
Бренд: Garland Страницы: 20
Yale MPB040-E Manual preview
MPB040-E
Бренд: Yale Страницы: 130
A.O. Smith T-H2S-DV Troubleshooting Manual preview
T-H2S-DV
Бренд: A.O. Smith Страницы: 35
Cleveland AFF-1150-FTP Specifications preview
AFF-1150-FTP
Бренд: Cleveland Страницы: 2
Lennox 10ACC Series Unit Information preview
10ACC Series
Бренд: Lennox Страницы: 12
Biral 25-10 180 Installation And Operating Instructions Manual preview
25-10 180
Бренд: Biral Страницы: 156
Flotec FPSES2700A Owner'S Manual preview
FPSES2700A
Бренд: Flotec Страницы: 16
SGS GAST Quick Manual preview
GAST
Бренд: SGS Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды