background image

2

GB

Application

Thermostat mixers are designed for hot water supplies from 
pressurised storage heaters and offer the highest temperature 
accuracy when used in this way. Given sufficient output 
(min.18 kW or 250 kcal per min), electric or gas-fired 
instantaneous heaters are also suitable (displacement 
heaters).
Thermostat mixers cannot be used in conjunction with low-
pressure storage heaters.
All thermostat mixers are adjusted at the factory with a flow 
pressure of 3 bar on both sides.
An additional shut-off device is only required if draw-off points 
are connected to the lower outlet.

Technical Data

Minimum flow pressure without 
downstream resistances

0.5 bar

Minimum flow pressure with 
downstream resistances

1 bar

Max. operating pressure

10 bar

Recommended flow pressure

1 - 5 bar

Test pressure

16 bar

Flow rate at 3 bar flow pressure 

24 l/min

Max. water temperature at hot water inlet

80 

°

C

Recommended max. flow temperature
(for energy saving) 

60 

°

C

Safety stop

38 

°

C

Hot water temperature at supply connection min. 2

°

C higher 

than mixed water temperature.
Hot water connection - W - (-H-)

left

Cold water connection - K - (-C-)

right

Minimum flow rate

5 l/min

At a flow pressure over 5 bar it is recommended that a 
pressure reducing valve be fitted in the supply line.

Prevention of frost damage

When the domestic water system is drained, the thermostat 
mixers must be drained separately, since non-return valves 
are installed in the hot and cold water connections. The 
complete thermostat assembly and non-return valves must be 
unscrewed and removed.

New installation

- Prepare wall ready for mixer.

Drill holes for thermostat mixer and cut slots for pipes.

- Observe the installation depth in accordance with the 

instructions given on the mounting template, see Fig. [1].

x = Face of tiles
y = Front face of mounting template
z = Resting point for spirit level
- Align the mixer horizontally, vertically and parallel to the wall, 

see Fig. [2] (place a spirit level on the cams or face of the 
mounting template).

- Install concealed thermostat mixer module in wall and 

connect pipes, see Fig. [3]. The housing is provided with 
pre-drilled holes (A) to facilitate mounting the fitting to the 
wall, see Fig. [2].

-

Do not solder the connections between the pipes and 
housing

, otherwise the built-in non-return valves may be 

damaged.

- Seal the bottom outlet with screw plug supplied.

Note

!

-

The hot water supply must be connected on the left

 

(marked W (H) on housing)

 and the cold water supply on 

the right

 (marked K (C) on housing), 

as viewed from the 

operating position.

Checking pipes and thermostatic mixer module for leaks.

1. Remove screws (B) and fitting template (C), see Fig. [5].
2. Turn splined adapter (D) clockwise to the stop and 

pressure test the bath outlet, see Fig. [4].

3. Turn splined adapter (D) anticlockwise to the stop and 

pressure test the shower outlet.

4. Return splined adapter (D) to initial position (fitting closed) 

arrow (D1) facing upwards.

5. Reinstall fitting template (C), see Fig. [5].

Flush pipes thoroughly.

1. Remove screws (B) and fitting template (C), see Fig. [5].
2. Close the hot and cold water supplies.
3. Remove screw plug (F).
4. Remove non-return valve (G) and filter (H).
5. Install flushing plugs (I) in non-return valve seat recesses, 

see Fig. [6].

6. Open the hot and cold water supplies and flush pipes 

thoroughly.

7. Close the hot and cold water supplies and remove flushing 

plugs (I).

8. Install filter (H) and non-return valve (G), see Fig. [5].
9. Install screw plug (F).

10. Open the hot and cold water supplies.

11. Turn splined adapter (D) clockwise to the stop and flush 

the bath outlet thoroughly, see Fig. [4].

12. Turn splined adapter (D) anticlockwise to the stop and 

flush the shower outlet thoroughly.

13. Return splined adapter (D) to initial position (fitting closed) 

arrow (D1) facing upwards.

14. Reinstall mounting template (C), see Fig. [5].

Plaster and tile the wall.

Do 

not

 remove the fitting template before final installation.

For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - [email protected] 0844 556 1818   

Содержание 34 212































Отзывы: