4
English
Application
Operation is possible in conjunction with:
- Pressurized storage heaters
Operation is
not
possible with:
- Low-pressure storage heaters
(displacement water heaters)
Specifications
•
Flow rate at 45 psi flow pressure:
- Spout
approx. 24 L/min or 6.3 gpm
- Handshower
max. 7.5 L/min or 2 gpm
•
Flow pressure
- min.
7.25 psi
- recommended
14.5 - 72.5 psi
- greater than 72.5 psi, fit with pressure reducing valves
•
Max. operating pressure
145 psi
•
Test pressure
232 psi
•
Temperature
- max. (hot water inlet)
158
°
F
- thermal disinfection possible
•
Water connection
cold - Right hand
hot - Left hand
Notes
- Installation of backflow protection must comply with local
codes and regulations.
- An access panel must be provided for access to diverter unit
and hose connections.
- Major pressure differences between cold and hot water
supply should be avoided.
Installation
Layout dimensions to establish centers and proper clearances,
see dimensional drawings on page 1.
For deviation to the suggested installation, observe minimum
clearance required for escutcheon sizes.
Flush piping system prior and after installation of faucet
thoroughly!
Side valves,
see fig. [1] and [2].
•
Valve with a groove on the top edge of the cartridge (A)
should be mounted on the right (cold water) side.
•
Valve without a groove on the top edge of the cartridge (A)
should be mounted on the left (hot water) side.
1. Screw the mounting set (B) to the bottom of the thread of the
side valve (C).
Make sure that the rubber washer (B1) is on the top of the
metal washer (B2).
2. Insert the side valve (C) through the tub deck hole from
below.
3. Close the cartridges (clockwise for the hot side and counter-
clockwise for the cold side).
4. Place the escutcheon washer (D) on the deck tub and screw
down the handle with escutcheon (E) until it stops.
Be sure that the handle points away from the spout.
5. Tighten the mounting set (B) from below to secure the valve.
Handshower,
see fig. [3].
1. Install the escutcheon (O1) onto the guide (O).
2. Install the guide (O) through the mounting surface, insure
the escutcheon O-ring (P) is in place.
3. Secure with mounting set (R).
4. Insert shower hose (S) through guide (O) from above.
5. Tighten the shower hose (S) to the handshower (U).
Spout (25 168),
see fig. [4a].
1. Place the washer (I) on the tub deck and insert the spout (J)
from above.
2. Secure the spout with the mounting set (K).
3. Install t-pipe (L) to the spout.
4. Attach hoses (C2) onto the t-pipe (L).
Spout (25 170),
see fig. [4b].
1. Place the washer (I) on the tub deck and insert the spout (J)
from above.
2. Secure the spout with the mounting set (K).
3. Install the diverter (L) to the spout, gently guiding the lift rod
assembly (M) up through the center of the spout (J).
4. Tighten the lift rod knob (N) to lift rod assembly (M).
5. Attach hoses (C2) onto the diverter (L).
Connect faucet,
see fig. [5].
Connect the side valves to the water supply. Insure the
supplied washers are used for all connections.
The cold water supply should be connected on the right side
valve and the hot water supply to the left valve.
The shower hose (S) must be connected to the hose (C1).
Open cold and hot water supply and check connections
for leakage!
Maintenance
Inspect and clean all parts, replace as necessary and grease
with special grease.
Shut off cold and hot water supply!
I. Ceramic cartridge,
see fig. [6].
1. Remove lever (F).
2. Unscrew the ceramic cartridge (A) using a 17mm wrench.
3. Change complete ceramic cartridge (A) or O-ring (A1).
Observe the different replacement part numbers of the
cartridges,
see page 2.
II. Flow straightener,
see page 2.
Unscrew and clean flow straightener (13 952).
III. Check valve,
see fig. [5].
1. Disconnect hose (C1).
2. Remove check valve (V).
Assemble in reverse order.
Replacement parts,
see page 2 ( * = special accessories).
Care
Instructions for care of this faucet will be found in the Limited
Warranty supplement.
