background image

18 OM-DEES

Cleaning

1.   Suggested Tools
 

a.  Cleaner, such as Klenzade HC-10 or HC-32 from ECOLAB, Inc.

 

b.  Kettle brushes in good condition. 

 

c.  Sanitizer such as Klenzade XY-12. 

 

d.  Film remover such as Klenzade LC-30. 

 

e.  Spray Degreaser  

 

f. DeLimer/Descaler

2.   Precautions
 

Before cleaning, shut off the kettle by turning the thermostat dial to “OFF,” and 
shut off all electric power to the unit at a remote switch, such as the circuit 
breaker.

3.   Procedure

a. 

Clean food-contact surfaces as soon as possible after use. If the unit is in 
continuous use, thoroughly clean and sanitize the interior and exterior at 
least once every 12 hours.

b.  Scrape and flush out food residues. Be careful not to scratch the kettle 

with metal implements.

c. 

Prepare a hot solution of the detergent/ cleaning compound as instructed 
by the supplier. Clean the unit thoroughly. A cloth moistened with cleaning 
solution can be used to clean controls, housings, and electrical conduits.

d.  Rinse the kettle thoroughly with hot water, then drain completely.

e. 

As part of the daily cleaning program, clean soiled external and internal 
surfaces. Remember to check the sides of the unit and control housing.

f. 

To remove stuck materials, use a brush, sponge, cloth, plastic or rub-
ber scraper, or plastic wool with the cleaning solution. To reduce effort 
required in washing, let the detergent solution sit in the kettle and soak 
into the residue. Do NOT use abrasive materials or metal tools that might 
scratch the surface. Scratches make the surface harder to clean and 
provide places for bacteria to grow.

 

Do NOT use steel wool, which may leave particles in the surface and 
cause eventual corrosion and pitting.

WARNING 

KEEP WATER AND SOLUTIONS AWAY

FROM CONTROLS AND ELECTRICAL 

EQUIPMENT. NEVER SPRAY THE SUPPORT 

HOUSING OR ELECTRICAL CONNECTIONS.

CAUTION 

MOST CLEANERS ARE HARMFUL TO THE 

SKIN, EYES, MUCOUS MEMBRANES, AND 

CLOTHING. PRECAUTIONS SHOULD BE 

TAKEN. WEAR RUBBER GLOVES, GOGGLES 

OR FACE SHIELD, AND PROTECTIVE 

CLOTHING. READ THE WARNINGS AND 

FOLLOW THE DIRECTIONS ON THE LABEL OF 

THE CLEANER CAREFULLY.

CAUTION

NEVER LEAVE A SANITIZER IN CONTACT 

WITH STAINLESS STEEL SURFACES LONGER 

THAN 30 MINUTES. LONGER 

CONTACT CAN CAUSE CORROSION.

Scrapers or steel wool can harm 

the kettle surface.

Use only a sponge, cloth or plastic 

brush to clean the kettle.

Содержание DEES-40





























Отзывы: