Grizzly T27139 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

background image

Model T27139 (Mfd. Since 3/16)

-10

-

Power Connection

After you have completed all previous
setup instructions the tool is ready to be
connected to the power supply.

To avoid unexpected startups or property
damage, use the following steps whenever
connecting or disconnecting the tool.

To test run tool:

1. Clear all setup tools away from tool.

2. Remove collet nut and collet.

3. Connect tool to power supply.

4. Turn tool ON, verify motor operation,

and then turn tool

OFF. Tool should

run smoothly and without unusual
problems or noises.

Test Run

DO NOT start tool until all preceding
setup instructions have been per-
formed. Operating an improperly set
up tool may result in malfunction or
unexpected results that can lead to
serious injury, death, or tool/prop-
erty damage.

Serious injury or death can result
from using tool BEFORE under-
standing its controls and related
safety information. DO NOT operate,
or allow others to operate, tool until
information is understood.

Connecting Power

1. Turn tool power switch OFF (O).

2. Insert power cord plug into a matching

power supply receptacle. Tool is now
connected to power source.

Figure 5. Connecting power.

1. Turn tool power switch OFF.

2. Grasp molded plug and pull it com-

pletely out of receptacle. Do not pull by
cord as this may damage wires inside.

Disconnecting Power

Figure 6. Disconnecting power.

«
...
11
12
13
14
15
...
»

Содержание T27139

































Отзывы:

Нет отзывов

Похожие инструкции для T27139

Бренд: Gallagher Страницы: 104

Бренд: Nemtek Страницы: 17

Бренд: Nemtek Страницы: 10

Бренд: Velleman Страницы: 9

Бренд: Makita Страницы: 1

Бренд: Emcore Страницы: 13

HSP-176M-1500-HD

Бренд: Baileigh Industrial Страницы: 44

GREEN POWER CCTV BNC04124

Бренд: Pulsar Страницы: 8

Бренд: Kaindl Страницы: 19

Бренд: Westward Страницы: 9

Бренд: H3C Страницы: 15

Craftsman 113.213850

Бренд: Sears Страницы: 24

Бренд: Broadata Страницы: 22

Бренд: Timberline Tool Страницы: 6

Бренд: Bench Dogs Страницы: 5

Бренд: Circuit-test Страницы: 10

DiamondHone 314

Бренд: Chef'sChoice Страницы: 12

Бренд: Baileigh Industrial Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды