background image

Model T10875 (Mfd. Since 01/15)

-11-

SECTION 3: SETUP

The  following  are  needed  to  complete  the  setup 
process:

Description Qty
• 

Safety Glasses ........................................... 1

• 

Solvent/Cleaner .......................................... 1

• 

Shop Rags .................................................. 1

• 

Phillips Screw Driver #2 ............................. 1

Needed for Setup

Your  machine  was  carefully  packaged  for  safe 
transportation.  Remove  the  packaging  materials 
from  around  your  machine  and  inspect  it.  If  you 
discover any damage, please call us immediately 
at (570) 546-9663
 for advice. 

Save the containers and all packing materials for 
possible  inspection  by  the  carrier  or  its  agent. 
Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.

Unpacking

SUFFOCATION HAZARD!

Keep children and pets away 

from plastic bags or packing 

materials shipped with this 

machine. Discard immediately.

This machine presents 

serious injury hazards 

to untrained users. Read 

through this entire manu-

al to become familiar with 

the controls and opera-

tions before starting the 

machine!

Wear safety glasses during 

the entire setup process!

Содержание T10875









































Отзывы: