Model G0854 (Mfd. Since 08/18)
-91-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
Labels & Cosmetics (Front)
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
2101
P08542101
MACHINE ID LABEL
2110
P08542110
ENTANGLEMENT LABEL
2102
P08542102
NOTICE UNLOCK CONVEYOR LABEL
2111
P08542111
MODEL NUMBER LABEL
2103
P08542103
NOTICE DO NOT LEAN ON CONVEYOR LABEL
2112
P08542112
GRIZZLY.COM LABEL
2104
P08542104
NOTICE FEED PANEL POINT LABEL
2113
P08542113
GRIZZLY NAMEPLATE (LARGE)
2105
P08542105
ELECTRICITY LABEL
2114
P08542114
TOUCH-UP PAINT, GRIZZLY GREEN
2106
P08542106
WARNING HOT SURFACE LABEL
2115
P08542115
DISCONNECT POWER LABEL
2107
P08542107
WARNING SHARP CUTTER LABEL
2116
P08542116
READ MANUAL LABEL
2108
P08542108
NOTICE COMPONENTS POWERED UP LABEL
2117
P08542117
TOUCH-UP PAINT, GREY PUTTY
2109
P08542109
GLASSES/RESPIRATOR LABEL
2118
P08542118
CONVEYOR BELT TENSION LABEL
G0854
grizzly.com
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
NOTICE
DO NOT lean or place heavy
objects on panel feeder! Doing
so will cause panel feeder
misalignment and imprecise
height adjustments.
Loosen conveyor
housing lock
handle before
adjusting conveyor
elevation.
NOTICE
To avoid jams and poor edgebanding
results, DO NOT feed additional panels
into edgebander until end of leading
panel passes this point.
MODEL G0854
AUTOMATIC EDGEBANDER
Specifications
Power Supply: 220V, 1-Ph, 60 Hz, 15A
Full-Load Current: 12A
Feed Motor: 3/4 HP
Glue Spindle Motor: 1/3 HP
Flush Trim Motor: 3/4 HP
Min. Panel Width: 4-3/4"
Min. Panel Length: 11"
Panel Thickness (Min.-Max.): 1/2"–1-3/4"
Tape Thickness (Min.-Max.): 0.5–2mm
Required Air Supply: 100 PSI
Panel Feed Speed: 16 FPM
Glue Pot Capacity: 34 oz.
Weight: 633 lbs.
Date
S/N
Mfd. for Grizzly in Taiwan
To reduce the risk of serious personal injury while using this machine:
1. Read and understand owner’s manual before starting.
2. Always wear approved safety glasses and a respirator.
3. Only plug power cord into a grounded outlet.
4. Disconnect power and allow hot parts to cool before adjusting or servicing machine.
5. Make sure machine is properly set up and adjusted before starting.
6. Avoid getting entangled or caught in moving parts—tie back long hair, roll up sleeves,
and DO NOT wear loose clothing, gloves, or jewelry.
7. Never reach inside machine during operation.
8. Never touch moving parts and blades, or hot glue pot.
9. Avoid getting hands or clothing pulled into conveyor while feeding workpiece.
10. Keep all guards and covers in place during operation.
11. Never leave machine running while unattended.
12. Only operate in a well-ventilated area. DO NOT operate near flammables.
13. DO NOT modify machine in any way or operate with broken or damaged parts.
14. DO NOT operate when tired or under influence of drugs or alcohol.
15. DO NOT expose to rain or use in wet locations.
16. Prevent unauthorized use by children or untrained users; restrict access or disable
machine when unattended.
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
Loosen conveyor
housing lock
handle before
adjusting conveyor
elevation.
2101
2102
2103
2102
2104
2105
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
NOTICE
For best results and machine
performance, DO NOT insert
workpieces into panel feeder
until all components are fully
powered-up and reach speci
fied operating temperature.
2116
2117
2118
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
