manualshive.com logo in svg

Grizzly G0809, Руководство пользователя

Поделиться
Скачать
Grizzly G0809 Скачать руководство пользователя страница 51

Model G0809 (Mfd. Since 1/17)

-49-

Setting Outfeed 

Table Height (Jointer)

The  outfeed  table  height  must  be  even  with  the 
top of the cutterhead knives when they are posi-
tioned  at  top  dead  center.  If  the  outfeed  table  is 
set too low, there will be snipe. If the outfeed table 
is set too high, the workpiece will hit the edge of 
the outfeed table during operation, increasing the 
chance of kickback.

Before beginning this procedure, the knives must 
be properly set in the cutterhead (refer to 

Setting/

Replacing Knives (Jointer) on  Page  47  for 
detailed instructions). 

Tools Needed 

Qty

Straightedge 24

" ................................................ 1

To set outfeed table height:

1.  DISCONNECT MACHINE FROM POWER!

2.  Remove  cutterhead  guard,  fence,  and 

cabinet side access panel.

3.  Place  straightedge  on  outfeed  table  so  it 

extends over cutterhead.

4.  Use  motor  pulley  to  rotate  cutterhead  until 

one  knife  is  at  top  dead  center  (its  high-
est  point  during  rotation),  as  illustrated  in 

Figures 66–67.

Figure 66. Knife at top dead center.

Top Dead

Center

Figure 65. Gib bolt tightening sequence.

1 

4 

2 

3 

5.  Loosen  cutterhead  gib  bolts,  starting  in  the 

middle, and alternating back and forth until all 
gib bolts are loose, but not falling out.

 

The  first  time  you  set  or  replace  a  knife, 
remove gib and knife from cutterhead. Clean 
gib and clean inside cutterhead slot to remove 
all pitch or sawdust. Coat knife and gib with a 
metal protectant.

6.  Position knife jig over knife. Loosen gib bolts 

until knife is completely loose.

7.  Access  jack  screws  through  holes  in  cutter-

head. Using a hex wrench, rotate jack screws 
to raise or lower knife. When knife is set cor-
rectly, it will barely touch middle pad of knife 
jig  or  bottom  of  straightedge  in  each  of  the 
straightedge  positions.  Snug  gib  bolts  just 
tight  enough  to  hold  knife  in  place.  Repeat 
with remaining knives.

8.  Rotate  cutterhead  to  reveal  the  first  knife 

you  started  with.  Lightly  snug  all  gib  bolts, 
alternating  from  one  side  to  the  other,  and 
working from the ends to the middle. Repeat 
with remaining knives.

9.  Tighten each gib bolt in the same alternating 

manner as you did in the previous step.

10.  Make sure outfeed table is set even with the 

new knives at top dead center.

11.  Replace  cutterhead  guard  and  cabinet  rear 

access panel.

Figure 64. Jack screw access hole.

Jack 

Screw

Gib 

Bolt

8.  Rotate cutterhead to reveal the first knife you 

started  with.  Lightly  snug  all  gib  bolts  (see 

Figure 64),  alternating  from  one  side  to  the 
other,  and  working  from  the  middle  to  the 
ends (see 

Figure 65). Repeat with remaining 

knives.

Содержание G0809









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды