Grizzly G0783 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

Grizzly G0783 Скачать руководство пользователя страница 32

-30-

G0783 (Mfd. Since 05/15)

Hinge-Pin Ball Oilers

Lube Type ...Model T23963 or ISO 32 Equivalent
Lube Amount ..................................... 1–2 Pumps
Lubrication Frequency ........... 8 hrs. of Operation

Proper lubrication of the hinge-pin ball oilers
shown in

Figure 40, is done with a pump-type oil

can that has a tip wide enough to seal the ball oil
inlet. We do not recommend using metal needle
or lance-type tips, as they can push the ball too
far into the oiler, break the spring seat, and lodge
the ball in the oil galley.

Push the oil can nozzle tip against each ball oiler,
and pump oil can twice. If you see sludge and
contaminants coming out of the lubrication area,
continue pumping oil can until the oil runs clear,
and wipe away any excess oil.

Figure 40. Location of hinge-pin ball oilers.

Ball Oilers

Base Pivot

Lube Type ....... Model T23963 ISO 32 Equivalent
Lube Amount ........................................Thin Coat
Lubrication Frequency ........... 8 hrs. of Operation

Proper lubrication around the saw base pivot
allows for smooth rotation when adjusting the
miter angle.

If base pivot movement becomes difficult, apply a
small amount of oil to openings beside the miter
angle gauge and the pivot channel behind the
vise (see

Figure 41). Rotate the base back-and-

forth several times to distribute oil evenly.

Figure 41. Base pivot oil locations.

Oil Access

Pivot

Channel

Miter

Angle

Gauge

«
...
30
31
32
33
34
...
»

Содержание G0783

















































Отзывы:

Нет отзывов