Grizzly G0783 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 48

Grizzly G0783 Скачать руководство пользователя страница 31

G0783 (Mfd. Since 05/15)

-29-

Gearbox Oil

Lube Type ...Model T23962 or ISO 68 Equivalent
Lube Amount ............................................

1

⁄

2

Liter

Check/Add Frequency ..............................Weekly
Change Frequency ..................... Every 6 Months

Items Needed

Qty

Hex Wrench 8mm .............................................. 1
Open-End Wrench

7

⁄

8

" ....................................... 1

Drain Pan ........................................................... 1
Funnel ................................................................ 1
Additional Person .............................................. 1

To add/change gearbox oil:

1. DISCONNECT SAW FROM POWER!

2. Raise saw to upmost position, and remove

lever arm to access oil fill hole to allow oil to
drain more freely.

3. Place oil drain pan beneath saw gearbox,

and remove oil drain plug, located on bottom
side of gearbox (see

Figure 39).

4. Hold drain pan under drain plug, then tilt saw

gearbox forward, allowing oil to drain out.

5. Have an assistant hold headstock in place,

and replace drain plug.

6. Insert funnel into fill hole. Add approximately

1

⁄

2

-liter of ISO 68 or equivalent oil until oil level

is halfway in sight glass. Wait 10 seconds to
allow oil to settle in sight glass before taking
a reading.

7. Wipe away any excess oil and re-install lever

arm.

Vise Leadscrew

Lube Type ...Model T23962 or ISO 68 Equivalent
Lube Amount ........................................... Fill Cup
Lubrication Frequency ..............................Weekly

To lubricate vise leadscrew:

1. DISCONNECT MACHINE FROM POWER!

2. Using vise handwheel, close vise jaws.

3. Open each oil cup lid, and fill with ISO 68 or

equivalent oil, then move vise through its full
range of motion several times to disperse oil
along leadscrew.

4. Wipe away any excess oil.

Note: For best performance, periodically

clean leadscrew thoroughly with mineral
spirits or other degreaser and then relubri-
cate.

Figure 38. Oil cup leadscrew lubrication.

Vise Leadscrew

Leadscrew

Oil Cup

(1 of 2)

Figure 39. Oil fill and drain plug locations.

Oil Drain Plug

Oil Fill Hole

Sight Glass

«
...
29
30
31
32
33
...
»

Содержание G0783

















































Отзывы:

Нет отзывов