manualshive.com logo in svg

Grindmaster 1WD25-4, Руководство по обслуживанию

Поделиться
Скачать
Grindmaster 1WD25-4 Скачать руководство пользователя страница 3

Figure B

UNPACKING

Your dispenser is packed in 2 cartons: base pack and bowl pack.
Unpack base by opening bottom flaps.  See Figure A.

IMPORTANT NOTES:
1.  Do not leave base upside down as this can damage 

refrigeration system.

2.  Check that all 4 rubber feet are attached to legs after removing 

from base pad. Check base pad or carton for missing feet and 
replace on legs.

3.  Never lift from louvres/ventilation slots. Instead, place fingers 

under base plate.

INSTALLATION

1.  Place base on counter. 
2.  For heated units (HD15/WHD15) units only:

Install Safety Arms

Tools required: Phillips Head Screwdriver 
a) Place unit on its side so you have access to the bottom of the unit.
b) Line up arm holes so they line up to the holes on the bottom of the unit; arms 

will extend forward as shown in illustration. See Figure B.

c) Attach arms with screws provided.

3.  Leave sufficient air space (6”(15cm)) on sides (also rear of D35 triple) for proper 

airflow and efficient operation. See Figure C.
IMPORTANT: Failure to provide required airspace can damage unit.

4.  Plug into properly grounded, 3 prong outlet.
5.  Assemble bowl parts and drain trays. See Assembly instructions that follow.

See Figure D.

NOTE: See pages 8 - 9 for Installing Security Kit Instructions.

1. Roll chassis 

up-side down

2. Open bottom flaps. 

Fold back.

3. Hold flaps out of way. 

Roll the carton over.

4. Lift off carton. 

Remove bottom pad.

BOTTOM PAD

CHASSIS

Figure A

Figure D

SPRAY TUBE

3/8” TAB

BOWL

GUIDE PIN

CHASSIS

FRONT

COOLING 
PLATE

BEARING SLEEVE

IMPELLER

BOWL
GASKET

PUMP
COVER

LOCKDOWN 
WASHER

SET-UP

Crathco® Beverage Dispensers

Page 2

6” (15 cm)

(all units)

6” (15 cm)

(D35 only)

Figure C

Содержание 1WD25-4





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды