Grindmaster 1WD25-4 Скачать руководство пользователя страница 1

Страница: 1 / 28

Beverage Dispensers

Mini, Standard, Heated, Whipper and Super Bowl Models

Service Manual

Table of Contents

Unpacking ................................................. 2

Installation ................................................. 2

Assembly .................................................. 3-4

Disassembly .............................................. 5

Routine Maintenance .............................. 6

Helpful Hints ............................................. 6

Preventative Maintenance ....................... 7

Security Kit Installation ............................ 8-9

Service

Base Assembly Components .............

Installing Pump & Fan Motors ............

Replacement of Compressor

Overload and Relay .............................

Replacement of Temperature Control ..

Magnetic Lock ......................................

Evaporator Assembly ..........................

Refrigeration Test ................................

Trouble Shooting Guide ........................... 13

Exploded Views ......................................... 14-19

Wiring Diagrams ........................................ 20-24

Refrigeration

Schematic ............................................

Cap Tube Specs ..................................

Refrigerant Charges ...........................

Prior authorization must be obtained from
Grindmaster Corporation for all warranty claims.

Grindmaster Corporation™
4003 Collins Lane
Louisville, KY 40245 USA
(502) 425-4776 (800) 695-4500
(800) 568-5715 (Technical Service Only)
FAX (502) 425-4776
www.grindmaster.com

Grindmaster Corporation, 1996
PRINTED IN USA

Patents Pending
0404 Form #CC-375-05
Part #3275

Содержание 1WD25-4





























Результаты поиска

Содержание 1WD25-4

Отзывы:

Бренды по названию

Популярные бренды

Grindmaster 1WD25-4, Руководство по обслуживанию

Результаты поиска

Содержание 1WD25-4

Отзывы:

Бренды по названию

Популярные бренды