manualshive.com logo in svg

Grindmaster 1WD25-4, Руководство по обслуживанию

Поделиться
Скачать
Grindmaster 1WD25-4 Скачать руководство пользователя страница 11

BASE ASSEMBLY COMPONENTS (Refrigerated Unit)

Compressor

Pump Motor

(one for each bowl)

Evaporator

Assembly

Thermostat

and Power

Switches

Condenser

Condenser fan
and motor

Refrigeration 

Tubing

(Model D35 shown here)

INSTALLING PUMP AND FAN MOTORS: For All Models
Tools Required: Phillips screwdriver

1.  Disconnect from power.
2.  Remove cabinet panels.
3.  Disconnect wires leading from motor to terminal board and/or switch.
4.  Loosen bolts holding motor in place and replace with new motor.
NOTE: Loosen bolts that hold top tray to frames for easier pump motor installation. Retighten bolts after reassembly.
5.  Connect wires from new motor to terminal board and switch.
6.  Replace cabinet panels.
NOTE: When installing or repairing the pump it is important to adjust the magnetic lock. On page 5 are the instruc-
tions that should be followed for adjusting the magnetic lock (See Figure N).

REPLACEMENT OF COMPRESSOR OVERLOAD AND RELAY: (Figure Q)
For Standard, Whipper and Mini Models
1.  Disconnect from power and remove front panel.
2.  Remove plastic cover (A) and lock wire (E27s

have a nut to unscrew) (B) from compressor housing 
and note positions of overload (C), relay (D) and wiring.

3.  Disconnect overload (C) from housing and wires, put 

overload spring clip (E) on new overload, then rewire 
and replace in proper position on compressor.

4.  Pull off relay (D) and disconnect wires, then rewire and 

push new relay onto the compressor terminals (F).

5.  Replace plastic cover (A) and lock wire (B), front panel 

of dispenser and service cord to power supply.

Figure Q

E

C

F

A

B

D

F

SERVICE

Crathco® Beverage Dispensers

Page 10

Содержание 1WD25-4





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды