background image

 

LineIQ Battery Charger 

28 Aug 2012 Edition 1.0 Page 13 of 13 

Document No. : GSN-DC-103 

5.

 

MAINTENANCE & SERVICE 

5.1

 

Servicing 

There are no user serviceable parts inside the LineIQ Charger, and under normal conditions, 
no servicing is required. 

Before each use, check to make sure that the equipment and leads are in good order. 

5.2

 

Periodic maintenance and testing 

The  LineIQ  Charger  and  accessories  should  be  inspected,  tested  and  tagged  as  per  the 
normal procedures of your employer or responsible body. 

5.3

 

Equipment faults 

If  the  equipment  is  found  to  be  faulty  in  any  way,  it  should  be  returned  to  your  supplier  for 
service. 

5.4

 

Calibration 

The LineIQ Charger does not require calibration. 

5.5

 

Cleaning 

The  LineIQ  Charger  and  leads  should  be  cleaned  with  a  soft, moist  cloth  using  only  a  mild 
detergent. 

 

After cleaning, ensure that all equipment is thoroughly dry before use. 
Double check that all connectors and connector receptacles are completely 
dry. 

 

6.

 

GRIDSENSE SUPPORT SERVICES 

6.1

 

Operational problems 

If  you  have  any  questions  about  the  operation  of  the  LineIQ  Charger,  consult  the  LineIQ 
Battery Charger User Manual (this document). 

Updated documentation can be downloaded from the GridSense web site at: 

 

http://www.gridsense.com/support

 

 

6.2

 

Technical sales and assistance 

The LineIQ Charger is manufactured by CHK GridSense Pty Ltd, Unit 3 Ground Floor, 20-36 
Nancarrow  Avenue,  Meadowbank,  NSW  2114  Australia.  If  you  are  experiencing  any 
technical  problems,  or  require  any  assistance  with  the  proper  use  or  application  of  this 
instrument, please call our technical hotline:

 

NORTH AMERICA 

OTHER COUNTRIES 

Phone:  +1 916 372 4945 

Phone:  +61 2 8878 7700

 

Fax: 

+1 916 372 4948 

Fax: 

+61 2 8878 7788

 

Email: 

[email protected] 

Email: 

[email protected]

 

Web: 

http://www.gridsense.com/service

 

Web: 

http://www.gridsense.com/service

 

 

Содержание LineIQ














Отзывы: