background image

THREE-YEAR LIMITED WARRANTY

Greystone Energy warrants its enclosed product to be free from defects in materials and 
workmanship under normal use and service for a period of three years from date of 
manufacture. Greystone Energy makes no other express warranty for the enclosed prod-
uct. No agent, representative, dealer, or employee of the Company has the authority to 
increase or alter the obligations or limitations of this Warranty. The Company’s obligation 
of this Warranty shall be limited to the replacement of any part of the product which is 
found to be defective in materials or workmanship under normal use and service during 
the three year period commencing with the date of manufacture. After phoning Greystone 
Energy at 1-506-853-3057 for a Return Authorization number, send defective units post-
age prepaid to: 150 English Drive, Moncton, N.B. Canada E1E 4G7. Please include a note 

describing the malfunction and suspected cause of failure. The Company shall not be 
obligated to replace units which are found to be defective because of damage, unreason-
able use, modifications, or alterations occurring after the date of manufacture. In no case 
shall the Company be liable for any consequential or incidental damages for breach of 
this or any other Warranty, expressed or implied whatsoever, even if the loss or damage 
is caused by the Company’s negligence or fault. Some states do not allow the exclusion 
or limitation of incidental or consequential damages, so the above limitation or exclusion 
may not apply to you. This Warranty gives you specific legal rights, and you may also 
have other rights which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

IN-GE-DSD120-01-01 8 

I56-9201-000 

  

©2019 Greystone Energy. 5/6/2019

Содержание DSD120









Отзывы: